Electricity (Safety) Regulations 2010
Other citing documents: WorkSafe New Zealand: Energy Safety
Section:
17(1)(b)Context:
...(c) in relation to work done at alluvial mining operations, opencast mining operations, and quarrying operations, in accordance with AS/NZS 3007.Section:
61AAContext:
(1) An installation that is or will be located in an excavated area above ground (including an installation at an alluvial mining operation, opencast mining operation, or quarrying operation) must be installed, tested, inspected, and connected in accordance with AS/NZS 3007.Section:
78CContext:
(1) All mobile and relocatable mining electrical equipment and conductors supplying that equipment at an alluvial mining operation or quarrying operation must be... ...(b) tested, inspected, and connected so as to comply with AS/NZS 3007; and (c) installed or relocated in accordance with AS/NZS 3007. (2) Mobile and relocatable mining electrical equipment and conductors supplying that equipment at an alluvial mining operation or a quarrying operation may only be maintained or replaced in 1 or more of the following ways: (a) such that the equipment and conductors comply with AS/NZS 3007:...Section:
78DContext:
(2) The assessments referred to in subclause (1) must be carried out - (a) at least once annually; and (b) in accordance with AS/NZS 3007; and...Section:
78FContext:
(1) All mobile and relocatable mining electrical equipment and conductors supplying that equipment at an opencast mining operation must be... ...(b) tested, inspected, and connected so as to comply with AS/NZS 3007; and (c) installed or relocated in accordance with AS/NZS 3007. (2) Mobile and relocatable mining electrical equipment and conductors supplying that equipment at an opencast mining operation may only be maintained or replaced in 1 or more of the following ways: (a) such that the equipment and conductors comply with AS/NZS 3007:...Section:
78GContext:
(3) The assessments referred to in subclause (2)(b) must be carried out... ...(b) in accordance with AS/NZS 3007; and...Section:
Schedule 2Context:
AS/NZS 3007 means AS/NZS 3007:2013Section:
Schedule 8, Clause 7Context:
All prescribed electrical work done on low and extra-low voltage mining electrical equipment and conductors supplying that equipment must be tested... ...(c) in the case of equipment and conductors used or installed in an alluvial mining operation, an opencast mining operation, or a quarrying operation, in accordance with AS/NZS 3007; and...Section:
Schedule 8, Clause 9Context:
All high-risk prescribed electrical work done on mining electrical equipment and conductors supplying that equipment that are used or installed in an alluvial mining operation, an opencast mining operation, or a quarrying operation must be inspected in accordance with AS/NZS 3007.Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards:... ...(d) construction sites: AS/NZS 3012:...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(c) low voltage installations at demolition and constructions sites: in accordance with AS/NZS 3012:...Section:
78MContext:
(1) A mine operator of a tourist mining operation must ensure that - (a) mining electrical equipment and conductors supplying that equipment are installed, tested, and inspected so as to comply with AS/NZS 3012:Section:
Schedule 2Context:
AS/NZS 3012 (means) AS/NZS 3012:2010: Electrical installations—Construction and demolition sitesSection:
Schedule 2Context:
AS/NZS 60079.35.1 means AS/NZS 60079.35.1:2011Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-9 Ed 6.0 as modified by Annex ZZ of AS/NZS 60335.2.9:2009, including Amendment 1Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electrical portable outlet devicesSection:
Schedule 4, Clause 5Context:
Listed as a 2nd alternative Standard applicable to circuit-breakers for overcurrent protection for household and similar installations - circuit-breakers for AC operationSection:
Schedule 4, Clause 6Context:
Grinders, polishers, and disc-type sanders: Standard E in conjunction with IEC 60745-2-3 Ed 2.2 as modified by AS/NZS 60745.2.3:2013 (sic), or...Section:
4 InterpretationContext:
In these regulations, unless the context otherwise requires, ... ...telecommunications network voltage, in relation to telecommunications lines or equipment, means a voltage that is not greater than the limits specified in AS/NZS 60950.Section:
Schedule 2Context:
AS/NZS 60950 (means) AS/NZS 60950.1:2011: Information technology equipment - Safety - General requirements: including Amendment 1Section:
Schedule 4, Clause 9Context:
Information technology equipment: AS/NZS 60950.1:2011, or IEC 60950-1 Ed 2.1, as modified by Annex ZZ of AS/NZS 60950.1:2011; and for power supplies for IT equipment: AS/NZS 60950.1:2011, or IEC 60950-1 Ed 2.1, as modified by Annex ZZ of AS/NZS 60950.1:2011Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(e) all other connectable installations: AS/NZS 3001; (f) a site installation that is... ...(iv)Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations: (a) low voltage installatioSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) that has been imported must be issued in accordance with AS/NZS 3001, but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3001 (means) AS/NZS 3001:2008: Electrical Installations—Transportable structures and vehicles including their site supplies: including Amendment 1Section:
Schedule 2Context:
AS/NZS 62013.1 means AS/NZS 62013.1:2001: Caplights for use in mines susceptible to firedamp—General requirements—Construction and testing in relation to the risk of explosionSection:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to Standard B, in conjunction with IEC 60335-2-17 Ed 3.0Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-69 Ed 4.0 as modified by Annex ZZ of AS/NZS 60335.2.69:2012, or...Section:
Schedule 4, Clause 2Context:
Listed as an apllicable Standard for smoke detectorsSection:
Schedule 4, Clause 15Context:
Reeling and trailing cables (other than underground coal mining): AS/NZS 2802:2000, including Amendment 1Section:
Schedule 4, Clause 1Context:
Fans: Standard A, or Standard B, in conjunction with IEC 60335-2-80 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.80:2004, including Amendment 1Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-2 Ed 6.0 as modified by AS/NZS 60335.2.2:2010, including Amendment 1Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shock from direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.Section:
Schedule 2Context:
AS/NZS 1826 means AS/NZS 1826:2008Section:
Schedule 8, Clause 37Context:
37 Requirements for mining electrical equipment used or installed in ERZ0 or ERZ1 (4) In this clause, special protection “s” means special protection “s” for Group I as defined in AS/NZS 1826 or IEC 60079-33.AS/NZS 3112:2011 A1 Approval and test specification - Plugs and socket-outlets: Amendment 1:2012
CURRENT
Section:
23(1)Context:
An appliance is deemed to be electrically unsafe if... ...(d) the appliance is fitted with, or is an integral plug device that includes, a flat 2-pin or 3-pin plug with the dimensions specified in AS/NZS 3112 and is not designed to operate safely at standard low voltage; or...Section:
61(1)Context:
Every 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 and that is installed in, or in connection with...Section:
Schedule 2Context:
AS/NZS 3112 means AS/NZS 3112:2011 including Amendment 1Section:
Schedule 4, Clause 3Context:
Listed as a Standard for plugs and socket-outletsSection:
Schedule 8, Clause 6Context:
(1) If a 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 is, or is to be, fitted in low voltage mining electrical equipment, it must be...AS/NZS 3760:2010 A2 In-service safety inspection and testing of electrical equipment: Amendment 2
CURRENT
Section:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
80(2)Context:
A new fitting or appliance that is sold or offered for sale is deemed to be electrically safe if (a) it complies with (i) AS/NZS 3820; or...Section:
81(1)Context:
A test report or certificate of conformity that shows how that a low voltage or extra-low voltage fitting or appliance complies with AS/NZS 3820 or any standard listed in Schedule 4 is conclusive evidence, in the absence of proof to the contrary, of compliance with regulationSection:
83(3)Context:
A supplier declaration of conformity must... ...(b) contain a statement that the article complies with... ...(ii) AS/NZS 3820; or...Section:
9Context:
In New Zealand, the ambient temperature is deemed to be... ...(b) 25° Celsius for the purpose of manufacturing and testing fittings and appliances for compliance with AS/NZS 3820.Section:
Schedule 2Context:
AS/NZS 3820 means AS/NZS 3820:2009: Essential safety requirements for electrical equipment: including Amendment 1Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to interconnection couplers for household and similar equipmentSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric cables - polymeric insulated - multicore control cablesSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric flexible cordsSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to appliance couplers for household and similar general purposesSection:
Schedule 4, Clause 6Context:
Screwdrivers and impact wrenches: Standard E in conjunction with IEC 60745-2-2 Ed 2.1 as modified by Annex ZZ of AS/NZS 60745.2.2:2009Section:
Schedule 4, Clause 15Context:
Diesel powered machinery and ancillary equipment: Standard Q in conjunction with AS/NZS 4871.6:2013Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to cord extension socketsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated: (a) a refrigeration system (but not a refrigeration appliance): AS/NZS 1677.Section:
Schedule 2Context:
AS/NZS 1677.2 (means) AS/NZS 1677.2:1998: Refrigerating systems - Safety requirements for fixed applications: including Amendments 1 and 2Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shockfrom direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.Section:
Schedule 2Context:
AS/NZS 61000.3.2 (means) AS/NZS 61000.3.2:2007: Electromagnetic compatibility (EMC) - Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 amperes per phase): including Amendments 1 and 2 (sic)Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and aSection:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medicalSection:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
17(1)(b)Context:
...(c) in relation to work done at alluvial mining operations, opencast mining operations, and quarrying operations, in accordance with AS/NZS 3007.Section:
61AAContext:
(1) An installation that is or will be located in an excavated area above ground (including an installation at an alluvial mining operation, opencast mining operation, or quarrying operation) must be installed, tested, inspected, and connected in accordance with AS/NZS 3007.Section:
78CContext:
(1) All mobile and relocatable mining electrical equipment and conductors supplying that equipment at an alluvial mining operation or quarrying operation must be... ...(b) tested, inspected, and connected so as to comply with AS/NZS 3007; and (c) installed or relocated in accordance with AS/NZS 3007. (2) Mobile and relocatable mining electrical equipment and conductors supplying that equipment at an alluvial mining operation or a quarrying operation may only be maintained or replaced in 1 or more of the following ways: (a) such that the equipment and conductors comply with AS/NZS 3007:...Section:
78DContext:
(2) The assessments referred to in subclause (1) must be carried out - (a) at least once annually; and (b) in accordance with AS/NZS 3007; and...Section:
78FContext:
(1) All mobile and relocatable mining electrical equipment and conductors supplying that equipment at an opencast mining operation must be... ...(b) tested, inspected, and connected so as to comply with AS/NZS 3007; and (c) installed or relocated in accordance with AS/NZS 3007. (2) Mobile and relocatable mining electrical equipment and conductors supplying that equipment at an opencast mining operation may only be maintained or replaced in 1 or more of the following ways: (a) such that the equipment and conductors comply with AS/NZS 3007:...Section:
78GContext:
(3) The assessments referred to in subclause (2)(b) must be carried out... ...(b) in accordance with AS/NZS 3007; and...Section:
Schedule 2Context:
AS/NZS 3007 means AS/NZS 3007:2013Section:
Schedule 8, Clause 7Context:
All prescribed electrical work done on low and extra-low voltage mining electrical equipment and conductors supplying that equipment must be tested... ...(c) in the case of equipment and conductors used or installed in an alluvial mining operation, an opencast mining operation, or a quarrying operation, in accordance with AS/NZS 3007; and...Section:
Schedule 8, Clause 9Context:
All high-risk prescribed electrical work done on mining electrical equipment and conductors supplying that equipment that are used or installed in an alluvial mining operation, an opencast mining operation, or a quarrying operation must be inspected in accordance with AS/NZS 3007.Section:
100(1)(d)Context:
(d) to comply with AS/NZS 4836 or the certified design for all electrical work carried out on electrical equipment operating at low or extra-low voltage.Section:
Schedule 2Context:
AS/NZS 4836 means AS/NZS 4836:2011Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shock from direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.Section:
Schedule 2Context:
AS/NZS 4761.1 means AS/NZS 4761.1:2008Section:
Schedule 8, Clause 38Context:
38 Prescribed electrical work in relation to ERZ0 or ERZ1: (1) This clause applies from 1 January 2016. (2) A mine operator must ensure that no person does, or assists in doing, any prescribed electrical work in relation to mining electrical equipment used or installed in an ERZ0 or ERZ1 unless that person has, or is supervised by a person who has, the competencies for carrying out electrical work that are prescribed in AS/NZS 4761.1. (3) For the purpose of subclause (2), WorkSafe may, by notice in the Gazette, recognise any New Zealand Qualifications Authority unit standard, or any other national or international qualification, as demonstrating the minimum competencies prescribed in AS/NZS 4761.1AS/NZS 5033:2012 A2 Installation and safety requirements for photovoltaic (PV) arrays: Amendment 2
SUPERSEDED
Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(d) a photovoltaic array: AS/NZS 5033:...Section:
Schedule 2Context:
AS/NZS 5033:2012: Installation and safety requirements for photovoltaic (PV) arrays: including Amendments 1 and 2, subject to the following modification: In clause 4.4.1.5(c), after “metallic”, insert “high density PVC”.AS/NZS 60079.14:2009 Explosive atmospheres - Electrical installations design, selection and erection
SUPERSEDED
Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(b) an installation in a hazardous area: AS/NZS 60079.14:...Section:
Schedule 2Context:
AS/NZS 60079.14 (means) AS/NZS 60079.14:2009: Explosive atmospheres - Electrical installations design, selection and erection: including Amendment 1NZS 7901:2008 Electricity and gas industries - Safety management systems for public safety
SUPERSEDED
Section:
48(1)Context:
Every safety management system must comply with either (a) NZS 7901; or...Section:
48(2)Context:
Nothing in regulation 49 or 50 applies to safety management systems that comply with NZS 7901.Section:
51(1)Context:
Every safety management system must be regularly audited to confirm whether (a) the safety management system complies with NZS 7901 or regulations 49 and 50, as appropriate; and...Section:
Schedule 2Context:
NZS 7901 (means) NZS 7901:2008: Electricity and gas industries - Safety management systems for public safetySection:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
Transformers for shavers, power supply units for shavers, and shaver supply units: Standard N in conjunction with IEC 61558-2-5 Ed 2.0 as modified by AS/NZS 61558.2.5:2011, including Amendment 1, or...Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-5 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-5 Ed 5.2Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-6 Ed 5.2 as modified by Annex ZZ of AS/NZS 60335.2.6:2008, including Amendments 1 and 4Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-6 Ed 5.2 as modified by Annex ZZ of AS/NZS 60335.2.6:2008, including Amendments 1 and 4Section:
23(1)Context:
An appliance is deemed to be electrically unsafe if... ...(d) the appliance is fitted with, or is an integral plug device that includes, a flat 2-pin or 3-pin plug with the dimensions specified in AS/NZS 3112 and is not designed to operate safely at standard low voltage; or...Section:
61(1)Context:
Every 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 and that is installed in, or in connection with...Section:
Schedule 2Context:
AS/NZS 3112 means AS/NZS 3112:2011 including Amendment 1Section:
Schedule 4, Clause 11Context:
Mains socket-outlet mounted nightlights: Standard J in conjunction with IEC 60598-2-12 Ed 2.0 in conjunction with Annex J of AS/NZS 3112:2011Section:
Schedule 4, Clause 3Context:
Listed as a Standard for plugs and socket-outletsSection:
Schedule 8, Clause 6Context:
(1) If a 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 is, or is to be, fitted in low voltage mining electrical equipment, it must be...Section:
Schedule 4, Clause 11Context:
Portable general-purpose luminaires: Standard J in conjunction with IEC 60598-2-4 Ed 2.0 as modified by AS/NZS 60598.2.4:2005, including Amendment 1, or Standard K in conjunction with AS/NZS 60598.2.4:2005, including Amendment 1Section:
Schedule 4, Clause 11Context:
Luminaires with built-in transformers or convertors for filament lamps: ..or Standard K in conjunction with AS/NZS 60598.2.6:1998Section:
Schedule 4, Clause 11Context:
Handlamps: ...or Standard K in conjunction with AS/NZS 60598.2.8:2002Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-5 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-14 Ed 5.1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-21 Ed 5.2Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-59 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.59:2005, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-60 Ed 3.2Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-69 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.69:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-69 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.69:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-69 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.69:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-69 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.69:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 11Context:
Lighting chains: Standard J in conjunction with IEC 60598-2-20 Ed 3.0 as modified by AS/NZS 60598.2.20:2002, or Standard K in conjunction with AS/NZS 60598.2.20:2002Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-11 Ed 7Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-15 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-15 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-15 Ed 5.2Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-17 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.17:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-23 Ed 5.1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-30 Ed 4.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-31 Ed 4.2Section:
Schedule 4Context:
Standard A, or standard B, in conjunction with IEC 60335-2-41 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.41:2004, including Amendment 1Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-59 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.59:2005, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3Section:
Schedule 4Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-78 Ed 2.1AS/NZS 60079.17:2009 Explosive atmospheres - Electrical installations inspection and maintenance
SUPERSEDED
Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(b) work on installations in hazardous areas: AS/NZS 60079.17:...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(e) low voltage installations orther than domestic installations in hazardous areas: in accordance with AS/NZS 60079.17:Section:
Schedule 2Context:
AS/NZS 60079.17 (means) AS/NZS 60079.17:2009: Explosive atmospheres - Electrical installations inspection and maintenance.Section:
Schedule 8, Clause39Context:
(2) All other mining electrical equipment installed in an ERZ0 or ERZ1 must be maintained so as to comply with AS/NZS 60079.17.Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ... and NZS 6115Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) a site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medical facilities: NZS 6115:Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2AS/NZS 3100:2009 Approval and test specification - General requirements for electrical equipment
CURRENT
Section:
Schedule 4, Clause 2Context:
Listed as an apllicable Standard for smoke detectorsSection:
Schedule 4, Clause 1Context:
Appliances for skin exposure to ultraviolet and infrared radiation: Standard A, or Standard B, in conjunction with IEC 60335-2-27 Ed 5.0 as modified by AS/NZS 60335.2.27:2010Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-24 Ed 7.1 as modified by AS/NZS 60335.2.24:2010 including Amendment 1, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-24 Ed 7.0 as modified by AS/NZS 60335.2.24:2010Section:
Schedule 4Context:
Electrical appliances for use with aquariums and garden ponds: Standard A, or Standard B, in conjunction with IEC 60335-2-55 Ed 3.1 as modified by Annex ZZ of AS/NZS 60335.2.55:2011, or until 06/07/2013, Standard C in conjunction with IEC 60335-2-55 Ed 3.1 as modified by Annex ZZ of AS/NZS 60335.2.55:2004, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-59 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.59:2005, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor:... ...Standard B, in conjunction with IEC 60335-2-89 Ed 2.0 as modified by AS/NZS 60335.2.89:2010, including Amendment 1AS/NZS 3760:2010 A1 In-service safety inspection and testing of electrical equipment: Amendment 1
CURRENT
Section:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-24 Ed 7.1 as modified by AS/NZS 60335.2.24:2010 including Amendment 1, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-24 Ed 7.0 as modified by AS/NZS 60335.2.24:2010Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-24 Ed 7.1 as modified by AS/NZS 60335.2.24:2010 including Amendment 1, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-24 Ed 7.0 as modified by AS/NZS 60335.2.24:2010Section:
Schedule 4, Clause 1Context:
Until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-86 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.86:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 5Context:
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs): AS/NZS 61008.1:2011 or IEC 61008-1 Ed 3.0 as modified by AS/NZS 61008.1:2011 or...Section:
Schedule 4, Clause 15Context:
Electrical protection devices for mines and quarries: AS/NZS 2081:2011Section:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4... ...standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4, Clause 1Context:
Commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor:... ...Standard B, in conjunction with IEC 60335-2-89 Ed 2.0 as modified by AS/NZS 60335.2.89:2010, including Amendment 1Section:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to air-break switchesSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to control circuit devices and switching elements - proximity devices with defined behaviour under fault conditionsSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to control circuit devices and switching elements - electrical emergency stop device with mechanical latching functionSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 6Context:
Listed as a modifying Standard for IEC 60745-2-12 Ed 2.1, applicable to fittings and appliancesSection:
Schedule 4, Clause 6Context:
Listed as a modifying Standard for IEC 60745-2-6 Ed 2.2, applicable to fittings and appliancesSection:
Schedule 4, Clause 6Context:
Listed as a modifying Standard to applicable Standard IEC 60745-2-8 Ed 2.1Section:
Schedule 4, Clause 12Context:
Glow-starters for fluorescent lamps: AS/NZS 60155:2000, including Amendments 1 and 2, or IEC 60155 Ed 4.0, including Amendments 1 and 2, as modified by AS/NZS 60155:2000, including Amendments 1 and 2Section:
Schedule 4, Clause 12Context:
Electronic inverters and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes): Standard L in conjunction with AS/NZS 61347.2.10:2004, or...Section:
Schedule 4, Clause 12Context:
AC supplied electronic ballasts for fluorescent lamps: Standard L in conjunction with AS/NZS 61347.2.3:2004, or...Section:
Schedule 4, Clause 12Context:
DC supplied electronic ballasts for general lighting: Standard L in conjunction with AS/NZS 61347.2.4:2002, or...Section:
Schedule 2Context:
AS/NZS 1299 means AS/NZS 1299:2009Section:
Schedule 8, Clause 37Context:
37(2) All mining electrical equipment used or installed in an ERZ1 must be... ...(d) in the case of restrained plugs and sockets for working voltages of 3 300 or less,... ...(ii) certified as complying with AS/NZS 1299:Section:
Schedule 2Context:
AS/NZS 1747 means AS/NZS 1747:2003Section:
Schedule 8, Clause 26Context:
26 Standards for cables (2) When cables that are installed or used at an underground mining operation are - (a) repaired, they must be repaired and tested in accordance with AS/NZS 1747: (b) fitted with accessories, those accessories must be fitted in accordance with AS/NZS 1747.Section:
Schedule 2Context:
AS/NZS 1802 means AS/NZS 1802:2003Section:
Schedule 8, Clause 26Context:
26 Standards for cables (1) All cables installed or used at an underground mining operation must comply with the following standards: (a) in the case of reeling or trailing cables, AS/NZS 1802; and...Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shock from direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.Section:
17(2)(a)(iv)Context:
...in the case of a fibre optic cable erected on poles or other supports, the design and installation of the fibre optic cable is in accordance with AS/NZS 7000; and...Section:
Schedule 2Context:
AS/NZS 7000 means AS/NZS 7000:2010Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(d) a connectable installation in a pleasure vessel: AS/NZS 3004.2...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation (a) in a pleasure vessel must be issued in accordance with AS/NZSSection:
Schedule 2Context:
AS/NZS 3004.2 (means) AS/NZS 3004.2:2008: Electrical installations—Marinas and recreational boats—Recreational boats installationsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(d) a photovoltaic array: AS/NZS 5033:...Section:
Schedule 2Context:
AS/NZS 5033:2012: Installation and safety requirements for photovoltaic (PV) arrays: including Amendments 1 and 2, subject to the following modification: In clause 4.4.1.5(c), after “metallic”, insert “high density PVC”.AS/NZS 5033:2012 A1 Installation and safety requirements for photovoltaic (PV) arrays: Amendment 1
SUPERSEDED
Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(d) a photovoltaic array: AS/NZS 5033:...Section:
Schedule 2Context:
AS/NZS 5033:2012: Installation and safety requirements for photovoltaic (PV) arrays: including Amendments 1 and 2, subject to the following modification: In clause 4.4.1.5(c), after “metallic”, insert “high density PVC”.Section:
90(2)(a)Context:
The person must test the appliance and either (a) confirm that it is electrically safe in accordance with the following:... ...(iii) in the case of all other low or extra-low voltage appliances: AS/NZS 5762; or...Section:
Schedule 2Context:
AS/NZS 5762 means AS/NZS 5762:2011Section:
Schedule 2Context:
AS/NZS 60079.0 means AS/NZS 60079.0:2012Section:
Schedule 8, Various ClausesContext:
34 Use of equipment when safe levels of methane have been exceeded: ...(2) In this clause... ...certified EPL Ma, in relation to mining electrical equipment, means certified to the relevant standard for EPL Ma that is prescribed in AS/NZS 60079.0 or IEC 60079-0 for that fitting or appliance. 37 Requirements for mining electrical equipment used or installed in ERZ0 or ERZ1: ...(4) In this clause... ...certified EPL Ma, in relation to mining electrical equipment, means certified to the relevant standard for EPL Ma that is prescribed in AS/NZS 60079.0 or IEC 60079-0 for that fitting or appliance; certified EPL Mb, in relation to mining electrical equipment, means certified to the relevant standard for EPL Mb for that fitting or appliance as prescribed in AS/NZS 60079.0 or IEC 60079-0Section:
Schedule 4Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4 (and) standard B means IEC 60335-1 Ed 5.0 as modified by AS/NZS 60335.1:2011 (and) standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4... ...standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 5Context:
Electromagnetic remote-control switches (RCS): IEC 60669-1 Ed 3.2 as modified by AS/NZS 60669.1:2013 in conjunction with IEC 60669-2-2 Ed 3.0; and for Electronic switches: IEC 60669-1 Ed 3.2 as modified by AS/NZS 60669.1:2013 in conjunction with IEC 60669-2-1 Ed 4.1 as modified by AS/NZS 60669.2.1:2013, and for Isolating switches: IEC 60669-1 Ed 3.2 as modified by AS/NZS 60669.1:2013 in conjunction with IEC 60669-2-4, Ed 1.0; and for Time-delay switches (TDS): IEC 60669-1 Ed 3.2 as modified by AS/NZS 60669.1:2013 in conjunction with IEC 60669-2-3 Ed 3.0Section:
Schedule 4, Clause 6Context:
Listed as an azpplicable Standard to 'other' hand-held motor-operated electric tools, spray guns for non-flammable liquidsSection:
Schedule 4, Clause 15Context:
Distribution, control and auxiliary equipment: Standard Q in conjunction with AS/NZS 4871.2:2010Section:
Schedule 4, Clause 15Context:
Remote controls for mining equipment: AS/NZS 4240.1:2009 Remote control systems for mining equipment—Design, construction, testing, installation and commissioning, AS/NZS 4240.2:2009 Remote control systems for mining equipment—Operation and maintenance for underground metalliferous mining, AS/NZS 4240.3:2013 Remote control systems for mining equipment— Operation and maintenance for underground coal miningSection:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-69 Ed 4.0 as modified by Annex ZZ of AS/NZS 60335.2.69:2012, or...Section:
23(1)Context:
An appliance is deemed to be electrically unsafe if... ...(d) the appliance is fitted with, or is an integral plug device that includes, a flat 2-pin or 3-pin plug with the dimensions specified in AS/NZS 3112 and is not designed to operate safely at standard low voltage; or...Section:
61(1)Context:
Every 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 and that is installed in, or in connection with...Section:
Schedule 2Context:
AS/NZS 3112 means AS/NZS 3112:2011 including Amendment 1Section:
Schedule 4, Clause 11Context:
Mains socket-outlet mounted nightlights: Standard J in conjunction with IEC 60598-2-12 Ed 2.0 in conjunction with Annex J of AS/NZS 3112:2011Section:
Schedule 4, Clause 3Context:
Listed as a Standard for plugs and socket-outletsSection:
Schedule 8, Clause 6Context:
(1) If a 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 is, or is to be, fitted in low voltage mining electrical equipment, it must be...AS/NZS 3760:2010 A1 In-service safety inspection and testing of electrical equipment: Amendment 1
CURRENT
Section:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
Schedule 4, Clause 2Context:
Listed as an apllicable Standard for smoke detectorsSection:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-2 Ed 6.0 as modified by AS/NZS 60335.2.2:2010, including Amendment 1Section:
Schedule 4, Clause 1Context:
Commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor:... ...Standard B, in conjunction with IEC 60335-2-89 Ed 2.0 as modified by AS/NZS 60335.2.89:2010, including Amendment 1Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: ... ...(c) electric security fenceSection:
Schedule 2Context:
AS/NZS 3016 (means) AS/NZS 3016:2002: Electrical installations - Electric security fences: including Amendment 1Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated: (a) a refrigeration system (but not a refrigeration appliance): AS/NZS 1677.Section:
Schedule 2Context:
AS/NZS 1677.2 (means) AS/NZS 1677.2:1998: Refrigerating systems - Safety requirements for fixed applications: including Amendments 1 and 2Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(e) all other connectable installations: AS/NZS 3001; (f) a site installation that is... ...(iv) iSection:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations: (a) low voltage installatioSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) that has been imported must be issued in accordance with AS/NZS 3001, but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3001 (means) AS/NZS 3001:2008: Electrical Installations—Transportable structures and vehicles including their site supplies: including Amendment 1Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(f) a site installation that is... ...(ii) in a show or carnival: AS/NZS 3002; or...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(d) low voltage instaSection:
Schedule 2Context:
AS/NZS 3002 (means) AS/NZS 3002:2008: Electrical installations—Shows and carnivals, subject to the variation that references to AS/NZS 3439.4 must be read as references to AS/NZS 3439.4.2009AS/NZS 3004.1:2008 Electrical installations - Marinas and recreational boats - Part 1: Marinas
SUPERSEDED
Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(f) a site installation that is (i) in a marina: AS/NZS 3004.1; or...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(b) low voltage instaSection:
Schedule 2Context:
AS/NZS 3004.1 (means) AS/NZS 3004.1:2008: Electrical installations—Marinas and recreational boats - MarinasSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(e) an emergency power supply in a hospital: AS/NZS 3009Section:
Schedule 2Context:
AS/NZS 3009 (means) AS/NZS 3009:1998: Electric installations—Emergency power supplies in hospitalsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(f) a low voltage mains parallel generation system that is connected tSection:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated: (a) work on mains parallel generation systems: AS 4771.1 and AS/NZS 3010...Section:
Schedule 2Context:
AS/NZS 3010 (means) AS/NZS 3010:2005: Electrical installations - Generating setsSection:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: ... ...(c) electric security fenceSection:
Schedule 2Context:
AS/NZS 3016 (means) AS/NZS 3016:2002: Electrical installations - Electric security fences: including Amendment 1Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(b) an animal stunning or meat conditioning system: NZS 6116:...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(e) work on animal stunning appliances or meat conditioning appliances: NZS 6116.Section:
Schedule 2Context:
NZS 6116 (means) NZS 6116:2006: Safe application of electricity in the meat processing industrySection:
25(a)Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and aSection:
Schedule 2Context:
AS/NZS 2500 (means) AS/NZS 2500:2004: Guide to the safe use of electricity in patient careSection:
Schedule 2Context:
AS/NZS 3800 means AS/NZS 3800:2005Section:
Schedule 8, Clause 40Context:
40. Overhaul of mining electrical equipment in ERZ0 or ERZ1: Any overhaul of mining electrical equipment installed or used, or to be installed or used, in an ERZ0 or ERZ1 must be done in accordance with AS/NZS 3800.Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-2 Ed 6.0 as modified by AS/NZS 60335.2.2:2010, including Amendment 1Section:
schedule 4, Clause 5Context:
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs): AS/NZS 61009.1:2011, or IEC 61009-1 Ed 3.0 as modified by AS/NZS 61009.1:2011, or....Section:
Schedule 4, Clause 14Context:
Isolating transformers for the supply of medical locations: Standard N in conjunction with IEC 61558-2-15 Ed 2.0 as modified by AS/NZS 61558.2.15:2012, or...Section:
Schedule 4, Clause 15Context:
Reeling and trailing cables (other than underground coal mining): AS/NZS 2802:2000, including Amendment 1Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shockfrom direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.AS/NZS 3004.1:2008 Electrical installations - Marinas and recreational boats - Part 1: Marinas
SUPERSEDED
Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(f) a site installation that is (i) in a marina: AS/NZS 3004.1; or...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(b) low voltage instaSection:
Schedule 2Context:
AS/NZS 3004.1 (means) AS/NZS 3004.1:2008: Electrical installations—Marinas and recreational boats - MarinasSection:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(d) a connectable installation in a pleasure vessel: AS/NZS 3004.2...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation (a) in a pleasure vessel must be issued in accordance with AS/NZSSection:
Schedule 2Context:
AS/NZS 3004.2 (means) AS/NZS 3004.2:2008: Electrical installations—Marinas and recreational boats—Recreational boats installationsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(e) an emergency power supply in a hospital: AS/NZS 3009Section:
Schedule 2Context:
AS/NZS 3009 (means) AS/NZS 3009:1998: Electric installations—Emergency power supplies in hospitalsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(f) a low voltage mains parallel generation system that is connected tSection:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated: (a) work on mains parallel generation systems: AS 4771.1 and AS/NZS 3010...Section:
Schedule 2Context:
AS/NZS 3010 (means) AS/NZS 3010:2005: Electrical installations - Generating setsSection:
Schedule 4, Clause 3Context:
Until 30/12/2016, AS/NZS 3117:2007 is applicable to bayonet lampholdersSection:
Schedule 4, Clause 6Context:
Listed as an azpplicable Standard to 'other' hand-held motor-operated electric tools, spray guns for non-flammable liquidsSection:
Schedule 4, Clause 6Context:
Routers and trimmers: Standard E in conjunction with IEC 60745-2-17 Ed 3.0 or until 29/04/2014, standard F in conjunction with AS/NZS 60745.2.17:2003Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-21 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-21 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-23 Ed 5.1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-29 Ed 4.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-29 Ed 4.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-31 Ed 4.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-31 Ed 4.2Section:
Schedule 2Context:
AS/NZS 1826 means AS/NZS 1826:2008Section:
Schedule 8, Clause 37Context:
37 Requirements for mining electrical equipment used or installed in ERZ0 or ERZ1 (4) In this clause, special protection “s” means special protection “s” for Group I as defined in AS/NZS 1826 or IEC 60079-33.Section:
Schedule 2Context:
AS/NZS 1972 means AS/NZS 1972:2006Section:
Schedule 8, Clause 26Context:
26 Standards for cables... ...(b) for all other cables, AS/NZS 1972:Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ... and NZS 6115Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) a site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medical facilities: NZS 6115:Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2Section:
4 InterpretationContext:
In these regulations, unless the context otherwise requires, ... ...telecommunications network voltage, in relation to telecommunications lines or equipment, means a voltage that is not greater than the limits specified in AS/NZS 60950.Section:
Schedule 2Context:
AS/NZS 60950 (means) AS/NZS 60950.1:2011: Information technology equipment - Safety - General requirements: including Amendment 1Section:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4... ...standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-31 Ed 4.2Section:
Schedule 4, Clause 1Context:
Fans: Standard A, or Standard B, in conjunction with IEC 60335-2-80 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.80:2004, including Amendment 1Section:
Schedule 4, Clause 11Context:
standard J means IEC 60598-1 Ed 7.0 as modified by Annex ZZ of AS/NZS 60598.1:2003; standard K means AS/NZS 60598.1:2003.AS/NZS 60598.2.1:1998 Luminaires - Particular requirements - Fixed general purpose luminaires
SUPERSEDED
Section:
Schedule 4, Clause 11Context:
Fixed general-purpose luminaires: ...or Standard K in conjunction with AS/NZS 60598.2.1:1998Section:
Schedule 4, Clause 11Context:
Recessed luminaires: Standard J in conjunction with IEC 60598-2-2 Ed 2.1 as modified by AS/NZS 60598.2.2:2001, including Amendment AAS/NZS 60598.2.4:2005 Luminaires - Particular requirements - Portable general purpose luminaires
CURRENT
Section:
Schedule 4, Clause 11Context:
Portable general-purpose luminaires: Standard J in conjunction with IEC 60598-2-4 Ed 2.0 as modified by AS/NZS 60598.2.4:2005, including Amendment 1, or Standard K in conjunction with AS/NZS 60598.2.4:2005, including Amendment 1Section:
Schedule 4, Clause 11Context:
Floodlights: Standard J in conjunction with IEC 60598-2-5 Ed 2.0 as modified by AS/NZS 60598.2.5:2002, or Standard K in conjunction with AS/NZS 60598.2.5:2002Section:
Schedule 4, Clause 11Context:
Photo and film luminaires (non-professional): ...or Standard K in conjunction with AS/NZS 60598.2.9:2006AS/NZS 60598.2.10:1998 Luminaires - Particular requirements - Portable child-appealing luminaires
SUPERSEDED
Section:
Schedule 4, Clause 11Context:
Listed as a 1st alternative Standard applicable to fittings and appliances, and as a modifying Standard to applicable Standards IEC 60598-2-10 Ed 1.2 and IEC 60598-2-10 Ed 2.0Section:
Schedule 4, Clause 11Context:
Luminaires for stage lighting, television, film, and photographic studios (outdoor and indoor): ...or Standard K in conjunction with AS/NZS 60598.2.17:2006Section:
Schedule 4, Clause 11Context:
Luminaires for swimming pools and similar applications: Standard J in conjunction with IEC 60598-2-18 Ed 2.0 as modified by Annex ZZ of AS/NZS 60598.2.18:1998, or Standard K in conjunction with AS/NZS 60598.2.18:1998Section:
Schedule 4, Clause 11Context:
Air handling luminaires: ...or Standard K in conjunction with AS/NZS 60598.2.19:2001Section:
Schedule 4, Clause 11Context:
Listed as a 1st alternative Standard applicable to fittings and appliances, and as a modifying Standard to applicable Standard IEC 60598-2-25 Ed 1.1Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 5Context:
Listed as a 2nd alternative Standard applicable to circuit-breakers for overcurrent protection for household and similar installations - circuit-breakers for AC operationAS/NZS 60598.2.2:2001 AA Luminaires - Particular requirements - Recessed luminaires: Amendment A
CURRENT
Section:
Schedule 4, Clause 11Context:
Recessed luminaires: Standard J in conjunction with IEC 60598-2-2 Ed 2.1 as modified by AS/NZS 60598.2.2:2001, including Amendment AAS/NZS 60598.2.22:2005 Luminaires - Particular requirements - Luminaires for emergency lighting
CURRENT
Section:
Schedule 4, Clause 11Context:
Luminaires for emergency lighting: ...or Standard K in conjunction with AS/NZS 60598.2.22:2005 as modified by Compliance Document for New Zealand Building Code Clause F6Section:
80(2)Context:
A new fitting or appliance that is sold or offered for sale is deemed to be electrically safe if (a) it complies with (i) AS/NZS 3820; or...Section:
81(1)Context:
A test report or certificate of conformity that shows how that a low voltage or extra-low voltage fitting or appliance complies with AS/NZS 3820 or any standard listed in Schedule 4 is conclusive evidence, in the absence of proof to the contrary, of compliance with regulationSection:
83(3)Context:
A supplier declaration of conformity must... ...(b) contain a statement that the article complies with... ...(ii) AS/NZS 3820; or...Section:
9Context:
In New Zealand, the ambient temperature is deemed to be... ...(b) 25° Celsius for the purpose of manufacturing and testing fittings and appliances for compliance with AS/NZS 3820.Section:
Schedule 2Context:
AS/NZS 3820 means AS/NZS 3820:2009: Essential safety requirements for electrical equipment: including Amendment 1Section:
70(1)Context:
Prescribed electrical work that must be certified must also be inspected if it is any of the following:... ...(b) work on installations that operate at high voltages (other than high voltage discharge lighting, where that lighting was installed in accordaSection:
Schedule 2Context:
AS/NZS 3832 (means) AS/NZS 3832:1998: Electrical installations - Cold-cathode illumination systemsSection:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(c) a stand-alone power system: AS/NZS 4509.1:...Section:
Schedule 2Context:
AS/NZS 4509.1 (means) AS/NZS 4509.1:2009: Stand-alone power systems - Safety and installationSection:
80(3)Context:
A used appliance that is sold or offered for sale is deemed to be electrically safe if, at the time it is sold or offered for sale,... ...(b) it has been disabled and marked in accordance with AS/NZS 4701; or...Section:
90(3)Context:
A person is deemed to comply with subclause (2)(b) if he or she disables and marks the appliance in accordance with AS/NZS 4701.Section:
Schedule 2Context:
AS/NZS 4701 (means) AS/NZS 4701:2000: Requirements for domestic electrical appliances and equipment for reconditioning or parts recyclingSection:
Schedule 2Context:
AS/NZS 61000.3.2 (means) AS/NZS 61000.3.2:2007: Electromagnetic compatibility (EMC) - Limits - Limits for harmonic current emissions (equipment input current less than or equal to 16 amperes per phase): including Amendments 1 and 2 (sic)Section:
Schedule 4, Clause 14Context:
Safety isolating transformers and power supply units for isolating transformers for general use: Standard N in conjunction with IEC 61558-2-6 Ed 2.0 as modified by AS/NZS 61558.2.6:2009Section:
Schedule 2Context:
AS/NZS 60079.29.2 means As/NZS 60079.29.2:2008Section:
Schedule 8, Clause 24Context:
24 Standards for gas monitors: (1) Where a gas monitoring system is used or installed at an underground metalliferous mining operation—(a) the flammable gas monitors must be selected, installed, used, and maintained so as to comply with AS/NZS 60079.29.2Section:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4... ...standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3Section:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to 'other' appliancesSection:
4 InterpretationContext:
In these regulations, unless the context otherwise requires, ... ...telecommunications network voltage, in relation to telecommunications lines or equipment, means a voltage that is not greater than the limits specified in AS/NZS 60950.Section:
Schedule 2Context:
AS/NZS 60950 (means) AS/NZS 60950.1:2011: Information technology equipment - Safety - General requirements: including Amendment 1Section:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4... ...standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and aSection:
80(3)Context:
A used appliance that is sold or offered for sale is deemed to be electrically safe if, at the time it is sold or offered for sale,... ...(c) in the case of a used electrical medical device, it is tested and marked in accordance with AS/NZ 3551.Section:
90(2)Context:
The person must test the appliance and either... ...(ii) in the case of low or extra-low voltage electrical medical devices: AS/NZS 3551:...Section:
91Context:
(1) The owner of an electrical medical device must ensure that the device is periodically assessed in accordance with AS/NZS 3551 to determine whether it is electrically safe and complies with that standard. (2) The results of each periodic assessment must be recorded in accordance with AS/NZS 3551, and the owner must retain the record.Section:
Schedule 2Context:
AS/NZS 3551 means AS/NZS 3551:2012Section:
Schedule 2Context:
AS/NZS 1747 means AS/NZS 1747:2003Section:
Schedule 8, Clause 26Context:
26 Standards for cables (2) When cables that are installed or used at an underground mining operation are - (a) repaired, they must be repaired and tested in accordance with AS/NZS 1747: (b) fitted with accessories, those accessories must be fitted in accordance with AS/NZS 1747.Section:
Schedule 2Context:
AS/NZS 1299 means AS/NZS 1299:2009Section:
Schedule 8, Clause 37Context:
37(2) All mining electrical equipment used or installed in an ERZ1 must be... ...(d) in the case of restrained plugs and sockets for working voltages of 3 300 or less,... ...(ii) certified as complying with AS/NZS 1299:Section:
80(2)Context:
A new fitting or appliance that is sold or offered for sale is deemed to be electrically safe if (a) it complies with (i) AS/NZS 3820; or...Section:
81(1)Context:
A test report or certificate of conformity that shows how that a low voltage or extra-low voltage fitting or appliance complies with AS/NZS 3820 or any standard listed in Schedule 4 is conclusive evidence, in the absence of proof to the contrary, of compliance with regulationSection:
83(3)Context:
A supplier declaration of conformity must... ...(b) contain a statement that the article complies with... ...(ii) AS/NZS 3820; or...Section:
9Context:
In New Zealand, the ambient temperature is deemed to be... ...(b) 25° Celsius for the purpose of manufacturing and testing fittings and appliances for compliance with AS/NZS 3820.Section:
Schedule 2Context:
AS/NZS 3820 means AS/NZS 3820:2009: Essential safety requirements for electrical equipment: including Amendment 1Section:
Schedule 2Context:
AS/NZS 60079.0 means AS/NZS 60079.0:2012Section:
Schedule 8, Various ClausesContext:
34 Use of equipment when safe levels of methane have been exceeded: ...(2) In this clause... ...certified EPL Ma, in relation to mining electrical equipment, means certified to the relevant standard for EPL Ma that is prescribed in AS/NZS 60079.0 or IEC 60079-0 for that fitting or appliance. 37 Requirements for mining electrical equipment used or installed in ERZ0 or ERZ1: ...(4) In this clause... ...certified EPL Ma, in relation to mining electrical equipment, means certified to the relevant standard for EPL Ma that is prescribed in AS/NZS 60079.0 or IEC 60079-0 for that fitting or appliance; certified EPL Mb, in relation to mining electrical equipment, means certified to the relevant standard for EPL Mb for that fitting or appliance as prescribed in AS/NZS 60079.0 or IEC 60079-0AS/NZS 60079.11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety ‘i’
CURRENT
Section:
Schedule 2Context:
AS/NZS 60079.11 means AS/NZS 60079.11:2011Section:
Schedule 4, Clause 8Context:
Listed as a Standard applicable to audio and video products, and power supplies for IT equipmentSection:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(e) all other connectable installations: AS/NZS 3001; (f) a site installation that is... ...(iv) iSection:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations: (a) low voltage installatioSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) that has been imported must be issued in accordance with AS/NZS 3001, but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3001 (means) AS/NZS 3001:2008: Electrical Installations—Transportable structures and vehicles including their site supplies: including Amendment 1Section:
25(a)Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: ... ...(b) electric fences: AS/NZSSection:
Schedule 2Context:
AS/NZS 3014 (means) AS/NZS 3014:2003: Electrical installations - Electric fences: including Amendment 1Section:
25(a)Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: ... ...(b) electric fences: AS/NZSSection:
Schedule 2Context:
AS/NZS 3014 (means) AS/NZS 3014:2003: Electrical installations - Electric fences: including Amendment 1Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: ... ...(c) electric security fenceSection:
Schedule 2Context:
AS/NZS 3016 (means) AS/NZS 3016:2002: Electrical installations - Electric security fences: including Amendment 1Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated: (a) a refrigeration system (but not a refrigeration appliance): AS/NZS 1677.Section:
Schedule 2Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ...AS/NZS 3003, ...Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated: (a) an installation intended for use with electrical medical devices: AS/NZS 3003...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (ii) in any other medical location: AS/NZS 3003Section:
Schedule 2Context:
AS/NZS 3003 (means) AS/NZS 3003:2003: Electrical installations—Patient areas of hospitals, medical and dental practices and dialyzing locationsSection:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(b) work on installations in hazardous areas: AS/NZS 60079.17:...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(e) low voltage installations orther than domestic installations in hazardous areas: in accordance with AS/NZS 60079.17:Section:
Schedule 2Context:
AS/NZS 60079.17 (means) AS/NZS 60079.17:2009: Explosive atmospheres - Electrical installations inspection and maintenance: Including Amendment 1Section:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to portable invertersSection:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards:... ...(e) film and television siteSection:
Schedule 2Context:
AS/NZS 4249 (means) AS/NZS 4249:1994: Electrical safety practices - Film, video and television sitesSection:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and aSection:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medicalSection:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2Section:
Schedule 4, Clause 6Context:
Cut-off machines: Standard E in conjunction with IEC 60745-2-22 Ed 1.0 as modified by AS/NZS 60745.2.22:2011Section:
Schedule 2Context:
AS/NZS 1802 means AS/NZS 1802:2003Section:
Schedule 8, Clause 26Context:
26 Standards for cables (1) All cables installed or used at an underground mining operation must comply with the following standards: (a) in the case of reeling or trailing cables, AS/NZS 1802; and...Section:
Schedule 4, Clause 1Context:
Commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor:... ...Standard B, in conjunction with IEC 60335-2-89 Ed 2.0 as modified by AS/NZS 60335.2.89:2010, including Amendment 1Section:
Schedule 2Context:
AS/NZS 3439 (means) AS/NZS 3439.4.2009: Low-voltage switchgear and control gear assemblies - Particular requirements for assemblies for construction sites (ACS)Section:
Schedule 4, Clause 5Context:
Low voltage switchgear assemblies for construction sites (ACS): AS/NZS 3439.4:2009Section:
26(4)Context:
A fitting described in subclause (1)(b) or (c) is deemed to be electrically safe if it is a fitting that is part of an installation and it complies with AS/NZS 3019.Section:
74(3)Context:
If the period since the last disconnection or isolation is more than 6 months, regulation 73 does not apply, but the person proposing to reconnect or restore supply must, before doing so, give or sight a certificate issued in accordance with section 3 of AS/NZS 3019 that—.....Section:
Schedule 2Context:
AS/NZS 3019 (means) AS/NZS 3019:2007: Electrical installations - Periodic verificationSection:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
Transformers for shavers, power supply units for shavers, and shaver supply units: Standard N in conjunction with IEC 61558-2-5 Ed 2.0 as modified by AS/NZS 61558.2.5:2011, including Amendment 1, or...Section:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - flexible cables (cords)Section:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to rubber insulated cables - rated voltage up to and including 450/750 V - cords and flexible cablesSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to switches, disconnectors, switch-disconnectors, and fuse-combination unitsAS/NZS 4871.1:2012 Electrical equipment for mines and quarries - Part 1: General requirements
CURRENT
Section:
Schedule 4, Clause 15Context:
standard Q means AS/NZS 4871.1:2012AS/NZS 60745.1:2009 Hand-held motor-operated electrical tools - Safety - General requirements
CURRENT
Section:
Schedule 4, Clause 6Context:
Listed as a modifying Standard for IEC 60745-1 Ed 4.0, applicable to fittings and appliancesSection:
Schedule 4, Clause 12Context:
Glow-starters for fluorescent lamps: AS/NZS 60155:2000, including Amendments 1 and 2, or IEC 60155 Ed 4.0, including Amendments 1 and 2, as modified by AS/NZS 60155:2000, including Amendments 1 and 2Section:
Schedule 4, Clause 12Context:
standard L means AS/NZS 61347.1:2002, and standard M means IEC 61347-1 Ed 2.1 as modified by AS/NZS 61347.1:2002.Section:
Schedule 4, Clause 12Context:
Miscellaneous electronic circuits used with luminaires: Standard L in conjunction with AS/NZS 61347.2.11:2003, or...Section:
Schedule 4, Clause 12Context:
DC supplied electronic ballasts for public transport: Standard L in conjunction with AS/NZS 61347.2.5:2002, or...Section:
Schedule 4, Clause 13Context:
Tungsten filament lamps for domestic and similar general lighting purposes: AS/NZS 60432.1:2007, or...Section:
Schedule 4, Clause 14Context:
Safety isolating transformers and power supply units for isolating transformers for general use: Standard N in conjunction with IEC 61558-2-6 Ed 2.0 as modified by AS/NZS 61558.2.6:2009Section:
Schedule 4, Clause 15Context:
Substations: Standard Q in conjunction with AS/NZS 4871.3:2010Section:
Schedule 4, Clause 15Context:
Remote controls for mining equipment: AS/NZS 4240.1:2009 Remote control systems for mining equipment—Design, construction, testing, installation and commissioning, AS/NZS 4240.2:2009 Remote control systems for mining equipment—Operation and maintenance for underground metalliferous mining, AS/NZS 4240.3:2013 Remote control systems for mining equipment— Operation and maintenance for underground coal miningSection:
Schedule 4, Clause 15Context:
Remote controls for mining equipment: AS/NZS 4240.1:2009 Remote control systems for mining equipment—Design, construction, testing, installation and commissioning, AS/NZS 4240.2:2009 Remote control systems for mining equipment—Operation and maintenance for underground metalliferous mining, AS/NZS 4240.3:2013 Remote control systems for mining equipment— Operation and maintenance for underground coal miningSection:
80(3)Context:
A used appliance that is sold or offered for sale is deemed to be electrically safe if, at the time it is sold or offered for sale (a) it is tested, inspected, and tagged in accordance with AS/NZS 5761; or...Section:
Schedule 2Context:
AS/NZS 5761 (means) AS/NZS 5761:2011: In-service safety inspection and testing - Second-hand electrical equipment prior to saleSection:
Schedule 4, Clause 6Context:
Cut-off machines: Standard E in conjunction with IEC 60745-2-22 Ed 1.0 as modified by AS/NZS 60745.2.22:2011Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ...AS/NZS 3003, ...Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated: (a) an installation intended for use with electrical medical devices: AS/NZS 3003...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (ii) in any other medical location: AS/NZS 3003Section:
Schedule 2Context:
AS/NZS 3003 (means) AS/NZS 3003:2003: Electrical installations—Patient areas of hospitals, medical and dental practices and dialyzing locationsSection:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-29 Ed 4.2Section:
Schedule 4, Clause 14Context:
standard N means IEC 61558-1 Ed 2.1 as modified by Annex ZZ of AS/NZS 61558.1:2008, including Amendment 1Section:
80(3)Context:
A used appliance that is sold or offered for sale is deemed to be electrically safe if, at the time it is sold or offered for sale,... ...(b) it has been disabled and marked in accordance with AS/NZS 4701; or...Section:
90(3)Context:
A person is deemed to comply with subclause (2)(b) if he or she disables and marks the appliance in accordance with AS/NZS 4701.Section:
Schedule 2Context:
AS/NZS 4701 (means) AS/NZS 4701:2000: Requirements for domestic electrical appliances and equipment for reconditioning or parts recyclingSection:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
17(2)(a)(iv)Context:
...in the case of a fibre optic cable erected on poles or other supports, the design and installation of the fibre optic cable is in accordance with AS/NZS 7000; and...Section:
Schedule 2Context:
AS/NZS 7000 means AS/NZS 7000:2010Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-76 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.76:2003, including Amendments 1 to 3Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4, Clause 6Context:
standard F means AS/NZS 60745.1:2003, including Amendments 1 to 3.Section:
Schedule 4, Clause 6Context:
standard F means AS/NZS 60745.1:2003, including Amendments 1 to 3.Section:
24(3)(c)Context:
24. Electrically unsafe RCDs (3) An RCD used to protect against electric shock, and that is either installed as part of an installation or is a portable RCD, is deemed to be electrically unsafe if it has a rated residual current exceeding 30 milliamperes and—... ...(c) it does not meet the limits specified in AS/NZS 3190.Section:
Schedule 2Context:
AS/NZS 3190 (means) AS/NZS 3190:2011: Approval and test specification—Residual current devices (current-operated earth-leakage devices)Section:
Schedule 4, Clause 5Context:
AS/NZS 3190:2011 is an applicable Standard for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) and residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs)Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ... and NZS 6115Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) a site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medical facilities: NZS 6115:Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2Section:
Schedule 2Context:
AS/NZS 4761.1 means AS/NZS 4761.1:2008Section:
Schedule 8, Clause 38Context:
38 Prescribed electrical work in relation to ERZ0 or ERZ1: (1) This clause applies from 1 January 2016. (2) A mine operator must ensure that no person does, or assists in doing, any prescribed electrical work in relation to mining electrical equipment used or installed in an ERZ0 or ERZ1 unless that person has, or is supervised by a person who has, the competencies for carrying out electrical work that are prescribed in AS/NZS 4761.1. (3) For the purpose of subclause (2), WorkSafe may, by notice in the Gazette, recognise any New Zealand Qualifications Authority unit standard, or any other national or international qualification, as demonstrating the minimum competencies prescribed in AS/NZS 4761.1AS/NZS 5033:2012 A1 Installation and safety requirements for photovoltaic (PV) arrays: Amendment 1
SUPERSEDED
Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(d) a photovoltaic array: AS/NZS 5033:...Section:
Schedule 2Context:
AS/NZS 5033:2012: Installation and safety requirements for photovoltaic (PV) arrays: including Amendments 1 and 2, subject to the following modification: In clause 4.4.1.5(c), after “metallic”, insert “high density PVC”.Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-5 Ed 5.2Section:
Schedule 4, Clause 5Context:
Type-tested and partially type-tested assemblies: AS/NZS 3439.1:2002Section:
Schedule 4Context:
Listed as a 2nd alternative Standard applicable to fittings and appliancesSection:
Schedule 4, Clause 1Context:
1 Household and similar electrical appliances: (1) In subclause (2), ... ...standard D means AS/NZS 3350.1:2002, including Amendments 1 to 4.Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-41 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.41:2004, including Amendment 1Section:
Schedule 4, Clause 6Context:
Grinders, polishers, and disc-type sanders: Standard E in conjunction with IEC 60745-2-3 Ed 2.2 as modified by AS/NZS 60745.2.3:2013 (sic), or until 31/05/2015, standard E in conjunction with IEC 60745-2-3 Ed 2.1 as modified by AS/NZS 60745:2011. NOTE: 2013 citation is an error, and should refer to 2011 edition, including all amendments.Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-30 Ed 4.2Section:
90(2)(a)Context:
The person must test the appliance and either (a) confirm that it is electrically safe in accordance with the following:... ...(iii) in the case of all other low or extra-low voltage appliances: AS/NZS 5762; or...Section:
Schedule 2Context:
AS/NZS 5762 means AS/NZS 5762:2011Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated: (a) a refrigeration system (but not a refrigeration appliance): AS/NZS 1677.Section:
Schedule 2Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(b) an installation in a hazardous area: AS/NZS 60079.14:...Section:
Schedule 2Context:
AS/NZS 60079.14 (means) AS/NZS 60079.14:2009: Explosive atmospheres - Electrical installations design, selection and erection: including Amendment 1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-11 Ed 7Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-6 Ed 5.2 as modified by Annex ZZ of AS/NZS 60335.2.6:2008, including Amendments 1 and 4Section:
Schedule 4Context:
1 Household and similar electrical appliances: (1) In subclause (2),—standard A means IEC 60335-1 Ed 4.2 as modified by Annex ZZ of AS/NZS 60335.1:2002, including Amendments 1 to 4 (and) standard B means IEC 60335-1 Ed 5.0 as modified by AS/NZS 60335.1:2011 (and) standard C means AS/NZS 60335.1:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 11Context:
Extra low voltage lighting systems for filament lamps: Standard J in conjunction with IEC 60598-2-23 Ed 1.1 as modified by AS/NZS 60598.2.23:2002, or Standard K in conjunction with AS/NZS 60598.2.23:2002Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
Schedule 4, Clause 14Context:
standard O means AS/NZS 61558.1:2000, including Amendments 1 to 7, and standard P means IEC 61558-1 Ed 1.1 as modified by Annex ZZ of AS/NZS 61558.1:2000, including Amendments 1 to 7.Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and appliances in medical locations:... ... and NZS 6115Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(c) a connectable installation in a mobile medical facility: NZS 6115:... ...(f) a site installations in mobile medical facilities: NZS 6115; or...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(c) work on installations intended for use with electrical medical devices situated in mobile medical facilities: NZS 6115:Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(f) low voltage and extra-low voltage installations intended for use with electrical medical devices situated— (i) in mobile medical facilities: in accordance with NZS 6115...Section:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that a warrant of electrical fitness for a connectable installation... ...(b) in a mobile medical facility must be issued in accordance with NZS 6115...Section:
Schedule 2Context:
NZS 6115 (means) NZS 6115:2006: Electrical installations - Mobile medical facilities: including Amendments 1 and 2Section:
26(4)Context:
A fitting described in subclause (1)(b) or (c) is deemed to be electrically safe if it is a fitting that is part of an installation and it complies with AS/NZS 3019.Section:
74(3)Context:
If the period since the last disconnection or isolation is more than 6 months, regulation 73 does not apply, but the person proposing to reconnect or restore supply must, before doing so, give or sight a certificate issued in accordance with section 3 of AS/NZS 3019 that—.....Section:
Schedule 2Context:
AS/NZS 3019 (means) AS/NZS 3019:2007: Electrical installations - Periodic verificationSection:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(b) an installation in a hazardous area: AS/NZS 60079.14:...Section:
Schedule 2Context:
AS/NZS 60079.14 (means) AS/NZS 60079.14:2009: Explosive atmospheres - Electrical installations design, selection and erection: including Amendment 1Section:
4 InterpretationContext:
In these regulations, unless the context otherwise requires, ... ...telecommunications network voltage, in relation to telecommunications lines or equipment, means a voltage that is not greater than the limits specified in AS/NZS 60950.Section:
Schedule 2Context:
AS/NZS 60950 (means) AS/NZS 60950.1:2011: Information technology equipment - Safety - General requirements: including Amendment 1Section:
Schedule 4, Clause 9Context:
Information technology equipment: AS/NZS 60950.1:2011, or IEC 60950-1 Ed 2.1, as modified by Annex ZZ of AS/NZS 60950.1:2011; and for power supplies for IT equipment: AS/NZS 60950.1:2011, or IEC 60950-1 Ed 2.1, as modified by Annex ZZ of AS/NZS 60950.1:2011AS/NZS 60079.14:2009 Explosive atmospheres - Electrical installations design, selection and erection
SUPERSEDED
Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(b) an installation in a hazardous area: AS/NZS 60079.14:...Section:
Schedule 2Context:
AS/NZS 60079.14 (means) AS/NZS 60079.14:2009: Explosive atmospheres - Electrical installations design, selection and erection: including Amendment 1AS/NZS 3112:2011 A1 Approval and test specification - Plugs and socket-outlets: Amendment 1:2012
CURRENT
Section:
23(1)Context:
An appliance is deemed to be electrically unsafe if... ...(d) the appliance is fitted with, or is an integral plug device that includes, a flat 2-pin or 3-pin plug with the dimensions specified in AS/NZS 3112 and is not designed to operate safely at standard low voltage; or...Section:
61(1)Context:
Every 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 and that is installed in, or in connection with...Section:
Schedule 2Context:
AS/NZS 3112 means AS/NZS 3112:2011 including Amendment 1Section:
Schedule 4, Clause 3Context:
Listed as a Standard for plugs and socket-outletsSection:
Schedule 8, Clause 6Context:
(1) If a 3-pin flat-pin socket-outlet that has the dimensions specified in AS/NZS 3112 is, or is to be, fitted in low voltage mining electrical equipment, it must be...Section:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards: (a) installations, fittings, and aSection:
80(3)Context:
A used appliance that is sold or offered for sale is deemed to be electrically safe if, at the time it is sold or offered for sale,... ...(c) in the case of a used electrical medical device, it is tested and marked in accordance with AS/NZ 3551.Section:
90(2)Context:
The person must test the appliance and either... ...(ii) in the case of low or extra-low voltage electrical medical devices: AS/NZS 3551:...Section:
91Context:
(1) The owner of an electrical medical device must ensure that the device is periodically assessed in accordance with AS/NZS 3551 to determine whether it is electrically safe and complies with that standard. (2) The results of each periodic assessment must be recorded in accordance with AS/NZS 3551, and the owner must retain the record.Section:
Schedule 2Context:
AS/NZS 3551 means AS/NZS 3551:2012AS/NZS 3760:2010 A2 In-service safety inspection and testing of electrical equipment: Amendment 2
CURRENT
Section:
26(2)Context:
A fitting or appliance described in subclause (1)(a) is deemed to be electrically safe if it has a current tag issued in accordance with AS/NZS 3760.Section:
26(3)(a)Context:
A fitting or appliance described in subclause (1)(b) or (c) is deemed to be electrically safe “(a) if it has a current tag issued in accordance with AS/NZS 3760; or....Section:
Schedule 2Context:
AS/NZS 3760 means AS/NZS 3760:2010 including Amendments 1 and 2.Section:
Schedule 4, Clause 5Context:
Electronic switches: IEC 60669-1 Ed 3.2 as modified by AS/NZS 60669.1:2013 in conjunction with IEC 60669-2-1 Ed 4.1 as modified by AS/NZS 60669.2.1:2013Section:
Schedule 4, Clause 14Context:
Transformers for shavers, power supply units for shavers, and shaver supply units: Standard N in conjunction with IEC 61558-2-5 Ed 2.0 as modified by AS/NZS 61558.2.5:2011, including Amendment 1, or...Section:
Schedule 4, Clause 15Context:
Mains powered electrical mobile machines: Standard Q in conjunction with AS/NZS 4871.4:2010Section:
Schedule 4, Clause 15Context:
Battery powered electrical mobile machines: Standard Q in conjunction with AS/NZS 4871.5:2010Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-108 Ed 1.0 as modified by Annex ZZ of AS/NZS 60335.2.108:2008Section:
24(6)Context:
Where an RCD is required by AS/NZS 3000 to be installed to protect children from the risk of electric shock from direct contact, the RCD is deemed to be electrically unsafe if ...Section:
4 InterpretationContext:
(3) A term used in these regulations and not defined in the Act or these regulations, and to which subclause (2) does not apply, has the meaning given (if any), (a) in the case of installations, in AS/NZS 3000; and ...Section:
57Context:
(1) Every installation that operates at low voltage or extra-low voltage must comply with either Part 1 or Part 2 of AS/NZS 3000. (2) A person who installs any part of a low voltage installation must... ...(b) ensure that the installation complies with tSection:
58Context:
(1) Every declaration of conformity for a low voltage installation must... ...(b) confirm, in the case of an installation under Part 1 of AS/NZS 3000, that the design complies with regulation 59; and... (3) A declaration of conformity for a revenue meter, if made under this subclause, must— “(a) identify the method of installation to be used; and “(b) confirm that the method complies with Part 1 of AS/NZS 3000; and.... (4) A declaration of conformity signed by a person other than the installer may be treated by the installer as evidence that the design complies with Part 1 or 2 (as appropriate) of AS/NZS 3000.Section:
59(1)Context:
This regulation applies to an installation, or part of any installation, that is being installed in accordance with Part 1 of AS/NZS 3000, despite anything in that Part.Section:
60Context:
(1) A person who installs a domestic installation that has a maximum demand at or below 80 amperes single phase or 50 amperes per phase in multi-phase must ensure that the installation complies with Part 2 of AS/NZS 3000. (2) A person who installs any ofSection:
61AAContext:
(2) This regulation applies despite anything in Part 1 or Part 2 of AS/NZS 3000.Section:
64(2)Context:
For the purposes of section 79(1)(a) of the Act, the domestic electrical wiring work that an owner of premises may do is as follows:... ...(b) installing, extending, and altering subcircuits (including submains), but only if... ...(ii) the work is testedSection:
65Context:
(1) Every low voltage installation on which prescribed electrical work is done must be tested in accordance with AS/NZS 3000... ...(3) Despite subclause (1), prescribed electrical work done on low voltage AC railway signalling equipment must be tested inSection:
67(2)Context:
The following matters may also be confirmed in a certificate of compliance: (a) in relation to a completed new low voltage installation, that- (i) the installation has been installed in accordance with a design prepared in accordance with Part 1 of AS/NZSSection:
6AContext:
(2) In these regulations, high-risk prescribed electrical work means the prescribed electrical work (not being low-risk prescribed electrical work) that - (a) comprises or includes the installation, or adjustment of the settings, of any of the following: (i) an extra-low or low voltage installation that does not, or will not, comply with Part 2 of AS/NZS 3000:... ...(d) is work on low voltage AC railway signalling equipment except where the equipment has been tested in accordance with ECP 60 and the work has been carried out in accordance with AS/NZS 3000:...Section:
70Context:
(1) Prescribed electrical work that must be certified must also be inspected if it is any of the following: (a) work carried out in accordance with Part 1 of AS/NZS 3000:... ...(2) However, prescribed electrical work on low voltage railway signalling instSection:
72Context:
(1) A person who inspects prescribed electrical work done on an installation that complies with Part 1 of AS/NZS 3000 must carry out the inspection in accordance with that standard and in accordance with the verification process described in the declaratiSection:
78(2)Context:
Every warrant of electrical fitness for a connectable installation must be issued in accordance with AS/NZS 3001, except that... (c) ...but only after an assessment for compliance with Part 1 of AS/NZS 3000.Section:
Schedule 2Context:
AS/NZS 3000 (means) AS/NZS 3000:2007: Electrical installations (known as the Australian/New Zealand Wiring Rules): including Amendments 1 and 2, subject to the following modifications....Section:
Schedule 8, Clause 28Context:
(8) Coverings on cables must be protected against chemical corrosion in the manner provided for in AS/NZS 3000.Section:
Schedule 8, Clause 6Context:
(2) This clause applies despite anything in Part 1 or 2 of AS/NZS 3000 or in these regulations.Section:
60(2)Context:
A person who installs any of the following must ensure that the installation complies with Part 2 of AS/NZS 3000 and also with the standard indicated:... ...(f) a site installation that is... ...(ii) in a show or carnival: AS/NZS 3002; or...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(d) low voltage instaSection:
Schedule 2Context:
AS/NZS 3002 (means) AS/NZS 3002:2008: Electrical installations—Shows and carnivals, subject to the variation that references to AS/NZS 3439.4 must be read as references to AS/NZS 3439.4.2009Section:
80(2)Context:
A new fitting or appliance that is sold or offered for sale is deemed to be electrically safe if (a) it complies with (i) AS/NZS 3820; or...Section:
81(1)Context:
A test report or certificate of conformity that shows how that a low voltage or extra-low voltage fitting or appliance complies with AS/NZS 3820 or any standard listed in Schedule 4 is conclusive evidence, in the absence of proof to the contrary, of compliance with regulationSection:
83(3)Context:
A supplier declaration of conformity must... ...(b) contain a statement that the article complies with... ...(ii) AS/NZS 3820; or...Section:
9Context:
In New Zealand, the ambient temperature is deemed to be... ...(b) 25° Celsius for the purpose of manufacturing and testing fittings and appliances for compliance with AS/NZS 3820.Section:
Schedule 2Context:
AS/NZS 3820 means AS/NZS 3820:2009: Essential safety requirements for electrical equipment: including Amendment 1Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(c) a stand-alone power system: AS/NZS 4509.1:...Section:
Schedule 2Context:
AS/NZS 4509.1 (means) AS/NZS 4509.1:2009: Stand-alone power systems - Safety and installationAS/NZS 60079.17:2009 Explosive atmospheres - Electrical installations inspection and maintenance
SUPERSEDED
Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(b) work on installations in hazardous areas: AS/NZS 60079.17:...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(e) low voltage installations orther than domestic installations in hazardous areas: in accordance with AS/NZS 60079.17:Section:
Schedule 2Context:
AS/NZS 60079.17 (means) AS/NZS 60079.17:2009: Explosive atmospheres - Electrical installations inspection and maintenance.Section:
Schedule 8, Clause39Context:
(2) All other mining electrical equipment installed in an ERZ0 or ERZ1 must be maintained so as to comply with AS/NZS 60079.17.Section:
60(3)Context:
If a person installs any of the following so that it complies with Part 2 of AS/NZS 3000, the person must also ensure that the installation complies with the standards indicated:... ...(b) an animal stunning or meat conditioning system: NZS 6116:...Section:
72(2)Context:
A person who inspects the following kinds of prescribed electrical work must do so in accordance with AS/NZS 3000 and also the standard indicated:... ...(e) work on animal stunning appliances or meat conditioning appliances: NZS 6116.Section:
Schedule 2Context:
NZS 6116 (means) NZS 6116:2006: Safe application of electricity in the meat processing industrySection:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards:... ...(d) construction sites: AS/NZS 3012:...Section:
75(1)Context:
The owners and operators of the following installations must ensure that the installations are periodically assessed as set out below, to determine whether they are electrically safe and otherwise comply with these regulations:... ...(c) low voltage installations at demolition and constructions sites: in accordance with AS/NZS 3012:...Section:
78MContext:
(1) A mine operator of a tourist mining operation must ensure that - (a) mining electrical equipment and conductors supplying that equipment are installed, tested, and inspected so as to comply with AS/NZS 3012:Section:
Schedule 2Context:
AS/NZS 3012 (means) AS/NZS 3012:2010: Electrical installations—Construction and demolition sitesSection:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-102 Ed 1.1 as modified by Annex ZZ of AS/NZS 60335.2.102:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electric shaver supply unitsSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric cables - polymeric insulated - for working voltages up to and including 0.6/1 (1.2) kVSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - flexible cables (cords)Section:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to rubber insulated cables - rated voltage up to and including 450/750 V - cords and flexible cablesSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to contactors and motor-starters - AC semiconductor controllers and contactors for non-motor loadsSection:
25Context:
Despite anything in these regulations, the following installations, fittings, and appliances are deemed to be electrically safe if they comply with the standards indicated and are used in accordance with those standards:... ...(e) film and television siteSection:
Schedule 2Context:
AS/NZS 4249 (means) AS/NZS 4249:1994: Electrical safety practices - Film, video and television sitesSection:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-24 Ed 7.1 as modified by AS/NZS 60335.2.24:2010 including Amendment 1, or, until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-24 Ed 7.0 as modified by AS/NZS 60335.2.24:2010Section:
Schedule 2Context:
AS/NZS 60079.29.2 means As/NZS 60079.29.2:2008Section:
Schedule 8, Clause 24Context:
24 Standards for gas monitors: (1) Where a gas monitoring system is used or installed at an underground metalliferous mining operation—(a) the flammable gas monitors must be selected, installed, used, and maintained so as to comply with AS/NZS 60079.29.2Section:
Schedule 4, Clause 5Context:
Low voltage distribution boards intended to be installed in places where unskilled persons have access for their use: AS/NZS 3439.3:2002Section:
Schedule 4, Clause 5Context:
Assemblies for power distribution in public networks: AS/NZS 3439.5:2001Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-9 Ed 6.0 as modified by Annex ZZ of AS/NZS 60335.2.9:2009, including Amendment 1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-14 Ed 5.1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-15 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-15 Ed 5.2Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-17 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.17:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-102 Ed 1.1 as modified by Annex ZZ of AS/NZS 60335.2.102:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to cord-line switchesSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to edison screw lampholdersSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric cables - polymeric insulated - for working voltages up to and including 0.6/1 (1.2) kVAS/NZS 4961:2003 Electric cables - Polymeric insulated - For distribution and service applications
CURRENT
Section:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric cables - polymeric insulated - for distribution and service applicationsSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to cables for high voltage luminous discharge tube installationsSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to multiple function equipment - automatic transfer switching equipmentSection:
Schedule 4, Clause 12Context:
Starting devices (other than glow starters): Standard L in conjunction with AS/NZS 61347.2.1:2002, or...Section:
Schedule 4, Clause 12Context:
DC or AC supplied electronic step-down convertors for filament lamps: Standard L in conjunction with AS/NZS 61347.2.2:2007Section:
Schedule 4, Clause 12Context:
Ballasts for discharge lamps (excluding fluorescent lamps): Standard L in conjunction with AS/NZS 61347.2.9:2004, or...Section:
Schedule 4, Clause 13Context:
Tungsten-halogen lamps for domestic and similar general lighting purposes: AS/NZS 60432.2:2007, or...Section:
Schedule 4, Clause 13Context:
Tungsten-halogen lamps (non-vehicle): AS/NZS 60432.3:2007, or...Section:
Schedule 4, Clause 14Context:
standard N means IEC 61558-1 Ed 2.1 as modified by Annex ZZ of AS/NZS 61558.1:2008, including Amendment 1Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to socket-outlet adaptorsAS/NZS 3194:1993 A1 Approval and test specification - Electric shaver supply units: Amendment 1
SUPERSEDED
Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electric shaver supply unitsSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to portable electrical control or conditioning devicesSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to sewing machine couplersSection:
Schedule 4, Clause 4Context:
Listed as a Standard applicable to electric cables - polymeric insulated - for working voltages up to and including 450/750 VSection:
Schedule 4, Clause 5Context:
Listed as a Standard applicable to control circuit devices and switching elements - DC interface for proximity sensors and switching amplifiers (NAMUR)Section:
Schedule 4, Clause 12Context:
Glow-starters for fluorescent lamps: AS/NZS 60155:2000, including Amendments 1 and 2, or IEC 60155 Ed 4.0, including Amendments 1 and 2, as modified by AS/NZS 60155:2000, including Amendments 1 and 2Section:
Schedule 4, Clause 12Context:
DC supplied electronic ballasts for aircraft lighting: Standard L in conjunction with AS/NZS 61347.2.6:2002, or...AS/NZS 61347.2.8:2003 Lamp controlgear - Particular requirements for ballasts for fluorescent lamps
CURRENT
Section:
Schedule 4, Clause 12Context:
Ballasts for fluorescent lamps: Standard L in conjunction with AS/NZS 61347.2.8:2003, or...Section:
Schedule 4, Clause 13Context:
Self-ballasted lamps for general lighting services: AS/NZS 60968:2001, or...AS/NZS 60079.18:2011 Explosive atmospheres - Part 18: Equipment protection by encapsulation ‘m’
SUPERSEDED
Section:
Schedule 2Context:
AS/NZS 60079.18 means AS/NZS 60079.18:2011Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-21 Ed 5.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-31 Ed 4.2Section:
Schedule 4, Clause 1Context:
Standard A, or standard B, in conjunction with IEC 60335-2-59 Ed 3.2 as modified by Annex ZZ of AS/NZS 60335.2.59:2005, including Amendments 1 to 3Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-75 Ed 2.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-82 Ed 2.1Section:
Schedule 4, Clause 1Context:
Until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-86 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.86:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 1Context:
Until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-86 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.86:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-91 Ed 3.0Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-91 Ed 3.0Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-100 Ed 1.0Section:
Schedule 4, Clause 1Context:
Standard B, in conjunction with IEC 60335-2-102 Ed 1.1 as modified by Annex ZZ of AS/NZS 60335.2.102:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to 'other' appliancesSection:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to 'other' appliancesSection:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-60 Ed 3.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-75 Ed 2.2Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-78 Ed 2.1Section:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-82 Ed 2.1Section:
Schedule 4, Clause 1Context:
Until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-86 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.86:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 1Context:
Until 31/05/2015, standard A, or standard B, in conjunction with IEC 60335-2-86 Ed 2.1 as modified by Annex ZZ of AS/NZS 60335.2.86:2002, including Amendments 1 to 4Section:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to 'other' appliancesSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to ceiling rosesAS/NZS 3136:2001 Approval and test specification - Electrical equipment for spa and swimming pools
CURRENT
Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electrical equipment for spa and swimming poolsSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electrical equipment for spa and swimming poolsSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electrical equipment for spa and swimming poolsAS/NZS 61184:2007 Bayonet lampholders
SUPERSEDED
Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to bayonet lampholdersSection:
Schedule 4, Clause 1Context:
Appliances for skin exposure to ultraviolet and infrared radiation: Standard A, or Standard B, in conjunction with IEC 60335-2-27 Ed 5.0 as modified by AS/NZS 60335.2.27:2010Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to plugs, socket-outlets, and couplers for general industrial applicationSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to plugs and socket-outlets for stationary appliancesSection:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to air-break switchesSection:
Schedule 4, Clause 2Context:
Listed as a Standard applicable to air-break switchesSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to portable electrical control or conditioning devicesSection:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to cord extension setsSection:
Schedule 4, Clause 1Context:
Listed as a modifying Standard to applicable Standard IEC 60335-2-78 Ed 2.1Section:
Schedule 4, Clause 1Context:
Until 26/10/2015, standard A, or standard B, in conjunction with IEC 60335-2-17 Ed 2.2 as modified by Annex ZZ of AS/NZS 60335.2.17:2004, including Amendments 1 and 2Section:
Schedule 4, Clause 3Context:
Listed as a Standard applicable to electric shaver supply units, until 30/12/2016AS/NZS 60745.1:2003 Hand-held motor-operated electrical tools - Safety - General requirements
SUPERSEDED
Section:
Schedule 4, Clause 6Context:
standard F means AS/NZS 60745.1:2003, including Amendments 1 to 3.Section:
Schedule 4, Clause 6Context:
standard F means AS/NZS 60745.1:2003, including Amendments 1 to 3.