All services are temporarily suspended as we prepare to launch our new website. However, online library subscribers should still be able to view their standards. Click here for more information.

AS/NZS 4129:2008

Fittings for polyethylene (PE) pipes for pressure applications

This document has been re-assessed by the committee, and judged to still be up to date.

WARNING: SUPERSEDED Standard. This document has been replaced by

AS/NZS 4129:2020

Specifies requirements for fittings to be used with polyethylene pipe manufactured in accordance with AS/NZS 4130 or AS 2698.2 or POP-009. This Standard is applicable to fittings manufactured for the conveyance of water, fuel gas, and other fluids including compressed air.

Table of contents are automatically generated, and may not be 100% accurate.

Buy product

$149.40 NZD (ex GST)

$166.00 NZD (ex GST)

Click Buy for Online Library subscription

Preview sample of document

Amendment history

AS/NZS 4129:2008 A1 . - incorporated. Published 04/12/2013.

Supersedes

AS/NZS 4129:2000 as of 30/06/2008

Publishing information

Status: SUPERSEDED

Published: 29/06/2008

Pages: 64

Committee: PL/06

References

This document may make references to other documents. All referenced documents are displayed below.

Standards NZ References:

Overseas Standards References:

AS 1049 Telecommunication cables - Insulation sheath and jacket
ISO 3503 Assembled joints between fittings and polyethylene (PE) pressure pipes – Test of leakproofness under internal p
AS ISO 7.1 Pipe threads where pressure-tight joints are made on the threads - Dimensions tolerances and designation
ISO 3501 Assembled joints between fittings and polyethylene (PE) pressure pipes – Test of resistance to pull out
ISO 13954 Plastics pipes and fittings - Peel decohesion test for polyethylene electrofusion assemblies of nominal outsid
AS 1199.1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limi
AS 2129 Flanges for pipes valves and fittings
ISO 13955 Plastics pipes and fittings - Crushing decohesion test for polyethylene electrofusion assemblies
ISO 1167-1 Thermoplastic pipes fittings and assemblies for the conveyance of fluids - Determination of the resistance to
ISO 7686 Plastics pipes and fittings - Determination of opacity
ISO 9624 Polyethylene (PE) pipes for fluids under pressure - Mating dimensions of flange adaptors and loose backing flan
ISO 9080 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics mat
IEC 60529 Degrees of protection provided by enclosures (IP Code)
ISO 4065 Thermoplastic pipes - Universal wall thickness table
ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM A276 Standard Specification for Stainless Steel Bars and Shapes
ISO 13957 Plastics pipes and fittings - Polyethylene tapping tees - Test methods for impact resistance
EN 12117 Plastics Piping Systems. Fittings Valves and Ancillaries. Determination of Gaseous Flow Rate/Pressure Drop Rela
ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
ISO 3459 Polyethylene (PE) pressure pipes - Joints assembled with mechanical fittings - Internal under-pressure test met
ISO 13951 Plastics piping systems - Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to
AS 3688 Water supply - Metallic fittings and end connectors
ISO TR 11414 Plastics pipes and fittings - Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assembl
ISO 1043-1 Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics
ISO 161-1 Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1:
AS 2345 Dezincificaton resistance of copper alloys
ISO TR 12176-1 Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1: Butt fusion
PIPA POP-009 Industry Guidelines - Polyethylene rural and flood pipe
ISO TR 10837 Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings
ISO 3126 Plastic pipe systems - Plastics components - Determination of dimensions
ISO 11413 Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an ele
AS 1145.2 Determination of tensile properties of plastics materials - Part 2: Test conditions for moulding and extrusion
ISO 13953 Polyethylene (PE) pipes and fittings - Determination of the tensile strength and failure mode of test pieces f
ISO 1167-2 Thermoplastic pipes fittings and assemblies for the conveyance of fluids - Determination of the resistance to
AS 1722.2 Pipe threads of Whitworth form - Part 2: Fastening pipe threads
AS 2193 Calibration and classification of force-measuring systems
AS 2698.2 Plastics pipes and fittings for irrigation and rural applications - Part 2: Polyethylene rural pipe
AS 9624 Polyethylene (PE) pipes for fluids under pressure - Mating dimensions of flange adaptors and loose backing flang
ISO 12176-2 Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion

Citations

This document is cited by New Zealand legislation. Expand the box to see details.

Building Code Compliance Document G12

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: AS1

Building Code Compliance Document G14

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: VM1

ICS codes

International Classification for Standards (ICS) is an international classification system for technical standards. It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

Follow these links to find other Standards similar to the one you are viewing.

83.140.30 Plastics pipes, fittings and valves

Other people who purchased this product also bought...

NZS 1170.5 Supp 1:2004
Structural design actions - Part 5: Earthquake actions - New Zealand Commentary
NZS 1170.5:2004
Structural design actions - Part 5: Earthquake actions - New Zealand
NZS 3910:2013
Conditions of contract for building and civil engineering construction
NZS 4404:2010
Land development and subdivision infrastructure
NZS 3604:2011
Timber-framed buildings

AS/NZS 4129:2008

Fittings for polyethylene (PE) pipes for pressure applications

Table of contents

Buy product

Amendment history

Supersedes

Publishing information

References

Citations

Building Code Compliance Document G12

Building Code Compliance Document G14

ICS codes

Other people who purchased this product also bought...

Fittings for polyethylene (PE) pipes for pressure applications

Methods of test for plastics pipes and fittings - Thermoplastics pipes, fittings and assemblies for the transport of fluids under pressure - Resistance to internal pressure