NZS 1170.5:2004

Structural design actions - Part 5: Earthquake actions - New Zealand

This document has been re-assessed by the committee, and judged to still be up to date.

The Building System Performance branch of MBIE has sponsored access to view and print a single downloadable PDF copy of this standard at no charge, which is available by clicking on this link.

Standards New Zealand also offers this standard to be purchased as Hard Copy or Online Library subscription.

Provides procedures for the determination of earthquake actions on structures in New Zealand. It gives the requirements for verification procedures, site hazard determination, the evaluation of structural characteristics, structural analysis for earthquake action effects, the determination and limits for deformations and the seismic design of parts of structures. It is to be applied in conjunction with AS/NZS 1170 parts 0, 1, 2 and 3. Appendices cover aspects of ultimate limit state design and the requirements for material specific structural design standards that are able to be used in conjunction with NZS 1170.5.

Table of contents are automatically generated, and may not be 100% accurate.

Buy product

$0.00 NZD (ex GST)

$180.00 NZD (ex GST)

Click Buy for Online Library subscription

Preview sample of document

Amendment history

NZS 1170.5:2004 A1 . - incorporated. Published 30/09/2016.

Supersedes

NZS 4203:1992 Volumes 1 & 2 as of 22/12/2004

Publishing information

Status: CURRENT

Published: 21/12/2004

Pages: 86

Committee: BD/6/4

References

This document may make references to other documents. All referenced documents are displayed below.

Standards NZ References:

Other References:

New Zealand Building Code Handbook and Approved Documents

Citations

This document is cited by New Zealand legislation. Expand the box to see details.

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 2.1(iv)

Citation Context:
Earthquake design loads in New Zealand are to be determined using... ...and NZS 1170.5.

Health and Safety at Work (Hazardous Substances—Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

Ministry: WorkSafe New Zealand
Section: Interpretation

Citation Context:
NZS 1170.5 means the New Zealand standard NZS 1170.5:2004 Structural design actions - Part 5: Earthquake actions - New Zealand

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 6.0

Citation Context:
Listed as a relevant standard

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 9.4

Citation Context:
The design of storage and transport frames should meet standards outlined in:... ...AS/NZS 1170 series: New Zealand structural design actions standard series.... ...Storage racks, frames and supports should be designed for the shape, size and weight of the precast concrete element, and to resist the loads and forces applied to them. Design should consider wind zones and ground conditions, and refer to the latest version of the following standards:... ...New Zealand structural design actions standard (AS/NZS 1170)

Traffic control devices manual - Part 3 - Advertising signs

Ministry: New Zealand Transport Agency
Section: 5.6

Citation Context:
The RSMA Compliance standard for traffic signs 2008 provides guidance and specifications for the design of frangible supports including reference to: • specific designs to Australian Standard/New Zealand Standard 1170 Structural Design Actions Set (AS/NZS1170)...

Building Code Compliance Document G12

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: AS2

HSNOCOP 59 Burners Complying with EN 746 - Revoked

Ministry: Environmental Protection Authority
Section: 5

Citation Context:
The standard AS 2121 specified in clause 6.2.1(b) Construction of AS 1375-1985 shall be substituted by NZS 1170.5: 2004 Structural Design Actions Part 5: Earthquake actions – New Zealand

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.2.3 Environmental loads

Citation Context:
Where appropriate, the environmental loads shall include the following: …Earthquake loads in accordance with AS/NZS 1170 (and supplements).

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 9.1.1

Citation Context:
Table 15 contains a general list of applicable relevant standards a number of which have been consulted in the preparation of the BPG. Additional information on particular standards and specific referencing are contained at various points throughout this

Health and Safety at Work (Hazardous Substances) Regulations 2017

Ministry: WorkSafe New Zealand
Section: 17.2

Citation Context:
NZS 1170.5:2004 means the New Zealand Standard on Structural design actions—Part 5: Earthquake Actions—New Zealand

Health and Safety at Work (Hazardous Substances) Regulations 2017

Ministry: WorkSafe New Zealand
Section: 17.6(3)

Citation Context:
A relevant PCBU must ensure that an above ground stationary tank used to store hazardous liquids is designed, constructed, and installed to (a) the seismic and wind loading requirements specified in... ...(iv) NZS 1170.5:2004; or...

Health and Safety at Work (Hazardous Substances—Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

Ministry: WorkSafe New Zealand
Section: 8(1)

Citation Context:
A relevant PCBU must ensure that the following primary load cases are applied to an FEA model:... ...(d) earthquake loads, Eu, derived from NZS 1170.5:...

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 6.4

Citation Context:
Falsework and temporary works should be designed to resist all reasonably foreseeable loads, including:... ...seismic loads for temporary structures in accordance with AS/NZS 1170.5.

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 6.7

Citation Context:
Seismic assessment of precast concrete elements on multi-storey structures requires a detailed structural analysis by a competent person. The design of the temporary support system should be in accordance with the ‘Parts and Components’ section of AS/NZS 1170.5.

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 2.2

Citation Context:
For New Zealand, the designer shall use the requirements of... ...and NZS 1170.5.

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: 2.4(3)(a)

Citation Context:
Designers shall ensure that all equipment or any alterations to equipment are designed in accordance with the appropriate standards specified in Appendix C of this code, or otherwise recognised by the Secretary. This includes taking into account any seism

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: Appendix C Referenced documents

Citation Context:
NZS 1170.5 Structural Design Actions – Earthquake Actions

Hazardous Substances (Dangerous Goods And Scheduled Toxic Substances) Transfer Notice 2004

Ministry: Environmental Protection Authority
Section: Schedule 8, Regulation 8(4)(a)(v)

Citation Context:
Every above ground stationary tank used to store hazardous liquids must be designed and constructed in accordance with ... AS/NZS 1170.5:2004 or ...

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.1.1

Citation Context:
Relevant standards are those related to… …This includes but is not limited to the following: ...NZS 1170.5 Structural design actions - Earthquake actions-New Zealand...

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 1.4

Citation Context:
NZS 1170.5 means the standard Structural design actions, Part 5: Earthquake actions – New Zealand

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 6.13.3 Falsework design

Citation Context:
In determining what information to consult and how to approach falsework design, no single document provides all the answers. Sources of information for scaffolders, chartered and design engineers include: …AS/NZS 1170 parts 0 - 3 and NZS 1170.5; ...

Building Code Compliance Document B1

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: VM1

ICS codes

International Classification for Standards (ICS) is an international classification system for technical standards. It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

Follow these links to find other Standards similar to the one you are viewing.

91.080 Structures of buildings

Other documents in this suite of Standards

Other people who purchased this product also bought...

AS/NZS 1170.3:2003
Structural design actions - Part 3: Snow and ice actions
NZS 3604:2011
Timber-framed buildings
AS/NZS 1170.1:2002
Structural design actions - Part 1: Permanent, imposed and other actions
AS/NZS 1170.0:2002
Structural design actions - Part 0: General principles
NZS 1170.5 Supp 1:2004
Structural design actions - Part 5: Earthquake actions - New Zealand Commentary

NZS 1170.5:2004

Structural design actions - Part 5: Earthquake actions - New Zealand

Table of contents

Buy product

Amendment history

Supersedes

Publishing information

References

Citations

ICS codes

Other people who purchased this product also bought...

This product is available as part of a set

Structural design actions - Part 2: Wind actions