AS/NZS 1170.2:2002

Structural design actions - Wind actions

This document has been re-assessed by the committee, and judged to still be up to date.

WARNING: SUPERSEDED Standard. This document has been replaced by

AS/NZS 1170.2:2011

Provides design values of wind actions for use in structural design. It is intended to be used in conjunction with AS/NZS 1170.0, which gives the procedure for structural design. Wind speeds and direction factors are provided for a range of probabilities of exceedance. Other factors cover the environment around the structure, the geometry of the structure and the dynamic interaction of the structure with the wind.

Table of contents are automatically generated, and may not be 100% accurate.

Buy product

$122.40 NZD (ex GST)

$136.00 NZD (ex GST)

Click Buy for Online Library subscription

Amendment history

AS/NZS 1170.2:2002 A1 . - incorporated. Published 03/04/2005.

Supersedes

NZS 4203:1992 Volumes 1 & 2 as of 05/02/2010

Publishing information

Status: SUPERSEDED

Published: 03/06/2002

Pages: 83

Committee: BD/06

References

This document may make references to other documents. All referenced documents are displayed below.

Standards NZ References:

AS/NZS 1170.0:2002
Structural design actions - Part 0: General principles

Overseas Standards References:

ISO 2394
AS 4040.3
ISO 4354

Other References:

Australian Building Codes Board - Building Code of Australia

Citations

This document is cited by New Zealand legislation. Expand the box to see details.

Code Of Practice For The Management Of Existing Stationary Container Systems Up To 60,000 Litres Capacity

Ministry: Environmental Protection Authority
Section: Appendix 3, Clause 1.4(3)

Citation Context:
An engineer experienced in the design of reinforced plastic tanks must undertake calculations substantiating the design of the tank, using the appropriate sections of NZS 3106: 1986 Code of practice for concrete structures for the storage of liquids, to determine the dynamic liquid loads; NZS 4203: 1992 Code of practice for general structural design and design loadings for buildings (or AS/NZS 1170, and NZS 4219: 1983 Specification for seismic resistance of engineering systems in buildings.

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.2.3 Environmental loads

Citation Context:
Where appropriate, the environmental loads shall include the following: Wind loads in accordance with AS/NZS 1170 (and supplements)...

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: 12.1(1)

Citation Context:
Wind forces are to be calculated as per the version of AS/NZS 1170.2 Structural Design Actions: Wind Actions applicable at the time of submission for design verification in New Zealand, or equivalent standards.

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: 11.1(1)

Citation Context:
The coefficient zone factor of 1.2 shall apply to all cranes. Wind forces are to be calculated as per AS/NZS 1170.2:2002 Structural design actions – Wind actions.

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: 16.1(2)

Citation Context:
Wind forces are to be calculated as per AS/NZS 1170.2: Structural Design Actions - Wind Actions. Refer to section 5.1.

Approved Code Of Practice For Cranes

Ministry: WorkSafe New Zealand
Section: Appendix C Referenced documents

Citation Context:
AS/NZS 1170.2 Structural Design Actions – Wind Actions

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.1.1

Citation Context:
Relevant standards are those related to… …This includes but is not limited to the following: ...AS/NZS 1170.2 Structural design actions - Wind actions...

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 6.13.3 Falsework design

Citation Context:
In determining what information to consult and how to approach falsework design, no single document provides all the answers. Sources of information for scaffolders, chartered and design engineers include: …AS/NZS 1170 parts 0 - 3 and NZS 1170.5; ...

ICS codes

International Classification for Standards (ICS) is an international classification system for technical standards. It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

Follow these links to find other Standards similar to the one you are viewing.

91.080 Structures of buildings

Other documents in this suite of Standards

Other people who purchased this product also bought...

NZS 1170.5 Supp 1:2004
Structural design actions - Part 5: Earthquake actions - New Zealand Commentary
AS/NZS 1170.2 Supplement 1:2002
Structural design actions - Part 2: Wind actions - Commentary (Supplement to AS/NZS 1170.2:2002)
AS/NZS 1170.1:2002
Structural design actions - Part 1: Permanent, imposed and other actions
NZS 1170.5:2004
Structural design actions - Part 5: Earthquake actions - New Zealand
AS/NZS 1170.0:2002
Structural design actions - Part 0: General principles

AS/NZS 1170.2:2002

Structural design actions - Wind actions

Table of contents

Buy product

Amendment history

Supersedes

Publishing information

References

Citations

ICS codes

Other people who purchased this product also bought...

Structural design actions - Part 2: Wind actions

Technical drawing - Structural engineering drawing