AS/NZS 1170.1:2002 (Reconfirmed 2016)

Structural design actions - Part 1: Permanent, imposed and other actions

This document has been re-assessed by the committee, and judged to still be up to date.

Provides design values of permanent, imposed and other actions to be used in the limit state design of structures and members. It is intended to be used in conjunction with AS/NZS 1170.0. Other actions covered include liquid pressure, ground water, rain water ponding and earth pressure.

Table of contents are automatically generated, and may not be 100% accurate.

Buy product

$67.50 NZD (ex GST)

$75.00 NZD (ex GST)

Click Buy for Online Library subscription

Preview sample of document

Amendment history

Supersedes

NZS 4203:1992 Volumes 1 & 2 as of 05/02/2010

Publishing information

Status: CURRENT

Published: 03/06/2002

Pages: 20

Committee: BD/06

References

This document may make references to other documents. All referenced documents are displayed below.

Standards NZ References:

Overseas Standards References:

ISO 2633:1974
AS 1720.2
AS 1657
AS 2867
AS 1735
AS 2156.1
AS 1418
ISO 2103:1986

Other References:

Australian Building Codes Board - Building Code of Australia

Citations

This document is cited by New Zealand legislation. Expand the box to see details.

Code Of Practice For The Management Of Existing Stationary Container Systems Up To 60,000 Litres Capacity

Ministry: Environmental Protection Authority
Section: Appendix 3, Clause 1.4(3)

Citation Context:
An engineer experienced in the design of reinforced plastic tanks must undertake calculations substantiating the design of the tank, using the appropriate sections of NZS 3106: 1986 Code of practice for concrete structures for the storage of liquids, to determine the dynamic liquid loads; NZS 4203: 1992 Code of practice for general structural design and design loadings for buildings (or AS/NZS 1170, and NZS 4219: 1983 Specification for seismic resistance of engineering systems in buildings.

Traffic control devices manual - Part 1 - General requirements for traffic signs

Ministry: New Zealand Transport Agency
Section: 7.2.3

Citation Context:
All overhead sign supports located within the clear zone must be specifically designed to Australian/New Zealand Standard 1170 Structural design action (AS/NZS 1170:2002) and be shielded behind an appropriately designed safety barrier.

Traffic control devices manual - Part 3 - Advertising signs

Ministry: New Zealand Transport Agency
Section: 5.6

Citation Context:
The RSMA Compliance standard for traffic signs 2008 provides guidance and specifications for the design of frangible supports including reference to: • specific designs to Australian Standard/New Zealand Standard 1170 Structural Design Actions Set (AS/NZS1170)...

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 2.1(iii)

Citation Context:
If it is found that roof loading is required, then the designer shall introduce additional loads as prescribed by AS/NZS 1170.1 with additional load combinations as per AS/NZS 1170.0.

Building Code Compliance Document B1

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: AS1, VM1, VM4

Building Code Compliance Document G12

Ministry: Ministry of Business, Innovation, and Employment: Building Systems Performance
Section: AS2

Health and Safety at Work (Hazardous Substances—Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

Ministry: WorkSafe New Zealand
Section: Interpretation

Citation Context:
AS/NZS 1170.1 means the Australian/New Zealand standard AS/NZS 1170.1:2002 Structural design actions – Part 1: Permanent, imposed and other actions

Health and Safety at Work (Hazardous Substances—Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

Ministry: WorkSafe New Zealand
Section: 7(8)

Citation Context:
A relevant PCBU must ensure that a tank that is designed to carry loads on its roof incorporates additional loads as prescribed by AS/NZS 1170.1 with additional load combinations as prescribed by AS/NZS 1170.0.

Health and Safety at Work (Hazardous Substances—Above Ground Rotationally-Moulded Polyethylene Stationary Tanks) Safe Work Instrument 2017

Ministry: WorkSafe New Zealand
Section: 25(2)

Citation Context:
If there is a risk of impact, the PCBU must ensure that a tank is protected by a protection barrier designed, and certified as designed, in accordance with AS/NZS 1170.1.

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 6.13.3 Falsework design

Citation Context:
In determining what information to consult and how to approach falsework design, no single document provides all the answers. Sources of information for scaffolders, chartered and design engineers include: …AS/NZS 1170 parts 0 - 3 and NZS 1170.5; ...

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 6.0

Citation Context:
Listed as a relevant standard

Best Practice Guideline For Scaffolding In New Zealand

Ministry: Scaffolding and Rigging New Zealand
Section: 1.2.1.1

Citation Context:
Relevant standards are those related to… …This includes but is not limited to the following: ...AS/NZS 1170.1 Structural design actions - Permanent, imposed and other actions...

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 6.3

Citation Context:
In areas where the potential risk of impact is medium or high, the tank is to be protected by a protection barrier with design loads based on AS/NZS 1170.1. Practical solutions include reinforced concrete walls and light gauge steelwork "W-Beam" roadside crash barriers. A structural design certificate for the barrier shall accompany the barrier installation to ensure that the barrier has been designed in a manner consistent with AS/NZS 1170.1.

HSNOCOP 61 Rotationally Moulded Polyethylene Storage Tanks for Non Flammable Hazardous Substances - Revoked

Ministry: Association of Rotational Moulders Australasia Inc
Section: 1.4

Citation Context:
AS/NZS 1170.1:2002 means the standard Structural design actions – Part 1: Permanent, imposed and other actions

Safe work with precast concrete

Ministry: WorkSafe New Zealand
Section: 9.4

Citation Context:
The design of storage and transport frames should meet standards outlined in:... ...AS/NZS 1170 series: New Zealand structural design actions standard series... ...Storage racks, frames and supports should be designed for the shape, size and weight of the precast concrete element, and to resist the loads and forces applied to them. Design should consider wind zones and ground conditions, and refer to the latest version of the following standards:... ...New Zealand structural design actions standard (AS/NZS 1170)

ICS codes

International Classification for Standards (ICS) is an international classification system for technical standards. It is designed to cover every economic sector and virtually every activity of the humankind where technical standards may be used.

Follow these links to find other Standards similar to the one you are viewing.

91.080 Structures of buildings

Other documents in this suite of Standards

Other people who purchased this product also bought...

AS/NZS 1170.2 Supplement 1:2002
Structural design actions - Part 2: Wind actions - Commentary (Supplement to AS/NZS 1170.2:2002)
NZS 1170.5 Supp 1:2004
Structural design actions - Part 5: Earthquake actions - New Zealand Commentary
AS/NZS 1170.1 Supplement 1:2002
Structural design actions - Part 1: Permanent, imposed and other actions - Commentary (Supplement to...
NZS 1170.5:2004
Structural design actions - Part 5: Earthquake actions - New Zealand
AS/NZS 1170.0:2002
Structural design actions - Part 0: General principles

AS/NZS 1170.1:2002 (Reconfirmed 2016)

Structural design actions - Part 1: Permanent, imposed and other actions

Table of contents

Buy product

Amendment history

Supersedes

Publishing information

References

Citations

ICS codes

Other people who purchased this product also bought...

This product is available as part of a set

Structural design actions - Part 0: General principles - Commentary